512484

Robomow Tuscania 500 Manual

95
Zoom out
Zoom in
Previous page
1/268
Next page
EN
41
Message
Displayed
Probable Cause/Event Corrective/User Action
- An unknown fault has occurred and user
help is required
- Manually drive/carry the mower away
from this particular area and restart
operation.
Start elsewhere
- Drive wheel motors have been working
under a severe load during automatic or
manual operation.
- Check to insure the mower is not stuck,
allowing the drive wheels to slip.
- Check the ground for holes or
indentions, where the mower has
stopped and fill it with dirt and level off.
- Check the drive wheels are free to
rotate and nothing block them.
- Remove the mower away from this
particular point and restart operation.
Start inside
- Automatic operation is initiated while
Robomow is placed out of the perimeter wire
lope.
- Place the mower inside the lawn and
press the ‘GO’ button.
- Robomow get stuck in place with no succeed
to continue driving.
- Check the ground for holes or
indentions, where the mower has
stopped and fill it with dirt and level off
– especially in the area close to the
perimeter, where the Robomow turns in
place.
Stuck in place
- Robomow has difficulty to turn in place
because the front wheel has fallen into hole
or indention and it caused the mower to turn
in place without detecting wire or bumper.
- Confirm the area is not too sloppy and
make sure to work in dry condition.
- Check the perimeter wire is not too
close to the edge – remove if required.
- Conform the mowing deck is not set too
low.
- There is an option to drive back to the
lawn in reverse before Robomow
perform the turn in place (contact your
service dealer for details).
Switch off
before lifting
- The user carries Robomow manually while
the main switch button is on.
- Switch off the main switch button before
carrying Robomow.
Switch off
before lifting
(While Robomow is
in the Base Station)
- Robomow does not detect the power from
the base Station, there is a charging problem
- Check the connection of the Base
Station board cables (red and black) to
the Base Station pins; confirm the
screws are tightened.
- Confirm good contact between
Robomow and the Base Station
charging pins.
- Make sure the pins are clean and not
corroded.
Time and date
- Displayed every time the batteries fuse is
taken out of the mower (reset operation)
- Set real time clock (day and hour) and
the date.
Time completed
- The operating time set for that zone has
been reached.
- Connect to the charger if all mowing has
been completed for the day.
Waiting for
signal…
- Robomow has stopped the operation,
because there is no signal detected.
- Check the power to the Base Station.
- There is electrical power interruption.
There is no need to do anything –
Robomow will renew automatically the
operation if the power will come back
within an hour from the break; if the
power will come back after more than
one hour, Robomow will drive back to
the Base Station for charging, but will
not renew the operation and mowing.
… 95 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow Tuscania 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow Tuscania 500 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 9,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info