512484

Robomow Tuscania 500 Manual

72
Zoom out
Zoom in
Previous page
1/268
Next page
EN
18
Add pegs in to pull
the perimeter wire down
to the ground surface,
below the grass tips.
Add pegs in to pull
the perimeter wire down
to the ground surface,
below the grass tips.
Important
If the lawn's edge borders with a pond, swimming pool or watercourse or where the grass level is
higher than 70cm (2ft) from the edge around it, then it is required to keep a distance of at least 1.2m
(4ft) between the wire and the water (or chasm) otherwise supplement a fence or the same along the
lawn's edge, so Robomow can detect it. The height must then be at least 15cm (6 inch). This will
prevent Robomow, under any circumstances, from crossing the wire outside the working area
1.4.3 Fastening the Wire to the Ground
It is not necessary to bury the perimeter wire, though you may do so if you wish, up to 10 cm
(4 inches) deep.
Small pegs or stakes are supplied with the Robomow and they are used to fasten and hold the
perimeter wire to the ground, below grass level.
Initially place a minimum number of pegs to fasten the wire down. Remember that you will want to
test the wire set up before you fill in additional pegs and you may find some areas where you will
need to move the wire position slightly.
Upon hammering the peg to its final depth in the ground, pull the wire tight. It is a lot easier to insert
pegs into wet soil. If the soil is dry, water the yard before perimeter wire set up.
Pegs should be driven at distances between one
another that will keep the wire down below the
grass level and prevent it from becoming a tripping
hazard (Figure 1.14).
When properly fastened to the ground, the wire and
pegs will soon disappear under the growth of new
grass and will not be visible.
If additional wire is required in order to complete
the set-up, use the wire connectors provided, which
are water-proof, to connect between the two wire
ends, as explained in chapter 5.6.
WARNING!
Damage to the eye is possible. Use proper eye protection and wear
appropriate work gloves when hammering the pegs. Hard or dry ground
may cause pegs to break when driving them in. In extreme cases,
watering the lawn where the pegs will be driven can be beneficial.
IMPORTANT INFORMATION!
Screw terminals or twisted cables, insulated with insulation tape is not a satisfactory splice. Soil
moisture will cause the stripped wire ends to oxidize and after a while result in broken circuit.
Figure 1.14 -
Pegging the Perimeter Wire
Short distance of
RoboRuler - where the
area outside the
immediate perimeter is
free of obstacles and is the
same relative height as the
perimeter edge or lower
Long distance of
RoboRuler – where the
area outside the
immediate perimeter has
obstacles or differences in
the height along the
perimeter edge
Figure 1.13 –
Using the RoboRuler
… 72 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow Tuscania 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow Tuscania 500 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 9,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info