512484

Robomow Tuscania 500 Manual

71
Zoom out
Zoom in
Previous page
1/268
Next page
EN
17
1.4 Perimeter Wire Setup
Now, knowing the location of the Base Station and the planning of the wire layout, you can begin to
setup the Perimeter Wire in the Base zone.
1.4.1 Starting Point
Place the Base Station according to your plan
with the fence towards the inner side of the
lawn;
Puncture the plastic covering of the perimeter
wire and pull the wire ends with the plot
connector out of the plastic covering; The
connector should be connected to the wire in
the polarity show in Figure 1.11;
The plastic covering is designed as a dispenser
for the wire; so do not remove the wire spool
from the covering;
Peg the beginning of the wire to the ground
where the Base Station will be located; be sure
to leave 30cm (12 inches) to close the loop at
the end of the setup (Figure 1.12);
Start laying the wire to the counterclockwise direction when standing inside the lawn, as show in
Figure 1.13.
Begin pulling the perimeter wire out of the plastic covering and lay it loosely as you walk along
the area of the lawn to the direction shown in Figure 1.13;
1.4.2 Laying Out the Perimeter Wire
Start setting the perimeter wire by placing pegs every few meters and at the lawn corners according
to your plan; do not forget obstacles that need to be demarcated while laying the wire.
After removing enough wire within a given section, use the RoboRuler provided to set the correct
distance from the lawn edge. The RoboRuler is used to help position the perimeter wire along walls,
fences, sidewalk, driveways, flowerbeds and other perimeter zones.
There are two basic measurements that are used on the RoboRuler (Figure 1.13).
The shorter distance is used along perimeter edges where the area outside the immediate
perimeter is free of obstacles and is the same relative height as the perimeter edge or lower
(sidewalk on the same level or flowerbeds).
The longer distance is used along perimeter edges where the area outside the immediate
perimeter has obstacles or differences in the height along the perimeter edge (walls and fences).
Figure 1.11 – Pull out the wire from the
plastic covering – do not remove the
covering; it is designed as a dispenser.
Figure 1.12 –
Direction of Perimeter Wire
layout from the Base Station
Leave 30cm (12 inches) at
the starting point, where the
Base Station is located
The Fence should be
inside lawn
Direction of wire layout
from the Base Station
Perimeter Wire –
do not remove the
plastic covering
… 71 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow Tuscania 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow Tuscania 500 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 9,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info