537227
19
Zoom out
Zoom in
Previous page
1/54
Next page
9
Initial Setup
EN
There should be a distance between the Island Wire and the Perimeter
Wire:
Maintain a minimum of 1.5 m (5 ft.) between the Island wire and
the Perimeter Wire.
Maintain a minimum of 1.5 m (5 ft.) between wires of adjacent
islands.
CAUTION: Setting the Perimeter Wire Anti Clockwise around the
obstacle will cause mower to drive into the island.
Complete bordering the island and return to the spot where you left the
lawn’s edge.
The wires leading to the Island and from it should be parallel and
touching.
Therefore, peg both wires, to and from the island, together with the
same pegs.
Robomow will not recognize these two wires.
It will mow over them as if they do not exist.
Robomow will recognize the single blocking wire around the
Perimeter Island and will not enter this area.
The minimum diameter of an Island should be 90 cm (3 ft.).
If protected objects are grouped closely together, demarcate them
by a single, continuous, Perimeter Island.
The minimum distance of the Perimeter Wire from the protected
area should be 32 cm (1 ft.).
Therefore, If protected objects are too close to the edge, leave
them out of the mowing area.
2.2.2 Setting a Narrow Pass
A pass connects two larger zones of the lawn. This pass may be narrow,
but it is wide enough to let Robomow drive through it.
The pass has to be at least 1.2 m (4 ft.) wide to allow Robomow to drive
through it.
Following the Perimeter Wire, Robomow drives between the Main Zone and
the Sub-Zone. But, while mowing each zone it does not cross over to the
other one.
If the pass is wider than 2 m (6.5 ft.) – there is NO need for any special
setting of the Perimeter Wire. Just include both the pass and the Sub-
Zone in the area covered by the Perimeter Wire.
If the pass is narrow: 1.2 – 2 m (4 to 6.5 ft.) -you have to set a special
Perimeter Wire configuration in order to lead Robomow in and out of
the pass.
A special Template is supplied with Robomow. It is folded on top of
the mower inside the box. You use this Template to set the Narrow
Pass.
This special setting of the Perimeter Wire will lead Robomow directly
into the Narrow Pass.
טיילפמטה לש םוליצ.
There should be a 40 cm (1.3 ft.) distance between the Perimeter Wire
and the pass entrance.
Pause the process of Perimeter Wire setting in order to prepare the
entrance to the Narrow Pass.
90
O
45
O
Perimeter Island - Min. 90 cm (3 ft.).
32 cm (1 ft.)
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow RS612 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow RS612 in the language / languages: English as an attachment in your email.

The manual is 7,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow RS612

Robomow RS612 User Manual - German - 54 pages

Robomow RS612 User Manual - Dutch - 54 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info