512472
47
Zoom out
Zoom in
Previous page
1/60
Next page
47
Message
Displayed
Probable Cause/Event Corrective/User Action
Splice wire
(Confirm the Base
Station beeps
continuously for cut
wire)
- Perimeter wire cut
- Wire disconnected from the Base
Station / Perimeter Switch
- Confirm wire is plugged in and wire leads are
firmly attached.
- Walk along perimeter, including islands and look
for obvious cuts or break in the wire. Repair with
Robomow wire splice connectors.
- In case the wire cut is not visible call your
service dealer for more information how to find
the wire cut.
- An unknown fault has occurred and
user help is required
- Manually drive/carry the mower away from this
particular area and restart operation.
Start elsewhere
- Drive wheel motors have been
working under a severe load during
automatic or manual operation.
- Check to insure the mower is not stuck, allowing
the drive wheels to slip.
- Check the ground for holes or indentions, where
the mower has stopped and fill it with dirt and
level off.
- Check the drive wheels are free to rotate and
nothing block them.
- Remove the mower away from this particular
point and restart operation.
Start inside
- Automatic operation is initiated while
Robomow is placed out of the
perimeter wire lope.
- Place the mower inside the lawn and press the
‘GO’ button.
- Robomow get stuck in place with no
succeed to continue driving.
- Check the ground for holes or indentions, where
the mower has stopped and fill it with dirt and
level off – especially in the area close to the
perimeter, where the Robomow turns in place.
Stuck in place
- Robomow has difficulty to turn in
place because the front wheel has
fallen into hole or indention and it
caused the mower to turn in place
without detecting wire or bumper.
- Confirm the area is not too sloppy and make
sure to work in dry condition.
- Check the perimeter wire is not too close to the
edge – remove if required.
- Conform the mowing deck is not set too low.
- There is an option to drive back to the lawn in
reverse before Robomow perform the turn in
place (contact your service dealer for details).
Switch off
before lifting
- The user carries Robomow
manually while the main switch
button is on.
- Switch off the main switch button before carrying
Robomow.
Switch off
before lifting
(While Robomow is
in the Base Station)
- Robomow does not detect the
power from the base Station, there
is a charging problem
- Check the connection of the Base Station board
cables (red and black) to the Base Station pins;
confirm the screws are tightened.
- Confirm good contact between Robomow and
the Base Station charging pins.
- Make sure the pins are clean and not corroded.
Time and date
- Displayed every time the batteries
fuse is taken out of the mower (reset
operation)
- Set real time clock (day and hour) and the date.
Time completed
- The operating time set for that zone
has been reached.
- Connect to the charger if all mowing has been
completed for the day.
Waiting for
signal…
- Robomow has stopped the
operation, because there is no
signal detected.
- Check the power to the Base Station.
- There is electrical power interruption. There is
no need to do anything – Robomow will renew
automatically the operation if the power will
come back within an hour from the break; if the
power will come back after more than one hour,
Robomow will drive back to the Base Station for
charging, but will not renew the operation and
mowing.
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow RM510 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow RM510 in the language / languages: English as an attachment in your email.

The manual is 3,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow RM510

Robomow RM510 User Manual - German - 60 pages

Robomow RM510 User Manual - Dutch - 60 pages

Robomow RM510 User Manual - French - 61 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info