512472
46
Zoom out
Zoom in
Previous page
1/60
Next page
46
Message
Displayed
Probable Cause/Event Corrective/User Action
No wire signal
- Base Station / Perimeter Switch is not turned
on or not connected to the zone intended to
mow.
- The perimeter wire is not connected to the
Base Station / Perimeter Switch
- The perimeter wire is cut
- Make sure the Base Station is
connected to the mains supply
- Disconnect the Base Station power
supply from the mains power and
reconnect after 10 seconds.
- Check the Perimeter Switch is
connected to the correct zone and is
turned on.
- Check the connection of the perimeter
wire to the Base Station / Perimeter
Switch.
- Check for cut in the perimeter wire.
Peg base
then press GO
- This message is displayed after ‘Base
position
’ test is completed successfully.
- Fasten the base in place using the 2
stakes (figure 1.30).
Rain detected
GO to ignore
- Robomow detects rain upon GO pressing
(received when pressing the GO button)
- Do not operate Robomow in rainy
weather and wet grass; If you choose to
override, press the ‘
GO’ button; The
overriding is valid for the current
operation only
Rain detected
Press GO
- Robomow has skipped the last depart due to
rain detection
- It is not recommended to cut wet or
damp grass, but if you choose to
override the rain sensor, change the
setting of the ‘Rain sensor’ to ‘off’ under
the ‘
Settings’ menu.
Rain detected
start delayed
- The operation is delayed as Robomow
detects rain on the scheduled time it should
start the automatic operation from the Base
Station.
- Do not do anything; the message is
displayed until the Robomow will not
detect rain for x hours (as defined in the
Delay after rain’ menu).
Rain sensor
disconnected
- Disconnection in the rain sensor wires. - Press ‘GO’ to confirm
Ready
keep charging
- The battery is fully charged (displayed when
charging through the standard power supply
and not through the Base Station)
- Keep the charger (power supply)
connected and operating
Recharge battery
- The maximum operating time has been
reached (displayed in non-Base Station
zone)
- Connect the charger to the mower
Remove fuse
before lifting
- Robomow was lifted while the battery fuse is
connected.
- Remove the fuse before lifting
Robomow.
Remove fuse then
check blade
- Some obstacle is stuck or wrapped around
the blade.
- Something is preventing a blade from
rotating freely. Severe grass accumulation
under the mowing deck; rope or similar
object wrapped around mowing blade.
- Object jammed under mower preventing
blade from rotating.
- CAUTION – Remove battery fuse
before lifting the mower.
- Inspect blades for foreign material or
debris preventing rotation.
- Clean out accumulated grass clippings
using a wooden stick.
Replace blade
every 200 hours
- An automatic reminder to replace the blades
is displayed every 200 hours
- Replace the blades and restart the
counter of the blades replacement
reminder by choosing the
‘Blades
replaced – Clear reminder
option
under the
‘Settings’ menu
Reposition base
- Robomow fails to enter the Base Station
during ‘Base position’ test
- Reposition the Base Station; usually it
should be placed with the marked lines
on the Base aligned with the perimeter
wire. If the Base is placed in narrow
pass, where the distance from the
adjacent wire is less than 3 meters, the
Base Station should be placed in shift
of few cm towards out of the lawn.
46


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow RM510 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow RM510 in the language / languages: English as an attachment in your email.

The manual is 3,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow RM510

Robomow RM510 User Manual - German - 60 pages

Robomow RM510 User Manual - Dutch - 60 pages

Robomow RM510 User Manual - French - 61 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info