512470
64
Zoom out
Zoom in
Previous page
1/84
Next page
Chapter 8-2
Robomow RL555, RL855, RL2000
Message Displayed Probable Cause/Event Corrective/User Action
Check Power
- Power supply/charger is not plugged properly
into the main power supply
- Charging plug is not fully inserted into the
charging socket of the mower
- The charging process has stopped due to a
temporary power loss.
Disconnect the charging plug from the mower, confirm power
supply is plugged into the main power receptacle and re-
connect the plug to the mower to resume charging.
- No power to receptacle or main power is shut
off
- Turn power on to the main receptacle.
- The mower contacts do not touch the Base
Station contacts
- Make sure that both mower drive wheels are leveled
with the Base Station base (if necessary fill the area
underneath the drive wheels with dirt)
- The mower or Base Station contacts are dirty - Clean the contacts with a brush or piece of cloth
- Charging is not detected, although there is
physical contact between the mower and the
Base Station contacts (mower is found in the
Base Station entrance).
- Confirm a good connection of the cables to the Base
Station contacts.
- Check the Charging fuse 5A (remove the plastic cover
below the Manual Controller).
- Mower does not reach the Base Station within
the time and distance limitations.
- Confirm the mower is operated in a Charging zone.
- Confirm the mower is not slipping or stuck on its way
to the Base Station.
Check signal
Press Go
- There is no fitting between the ‘Signal type’
setting in the menu and the signal jumper on
the Perimeter Switch;
- Automatic operation is initiated while
Robomow is placed out of the perimeter wire
lope.
- The perimeter wire is connected to the plot
connector in the wrong polarity.
- Robomow detects signal interferences
from adjacent activated lawn or from other
appliance activated near the zone;
- Set the ‘Signal type’ menu to ‘A and confirm the signal
jumper is installed on the Perimeter Switch board; or
alternatively set it to ‘B’ and remove the signal jumper
from the board;
- Place the mower inside the lawn and press the ‘GO’
button.
- Change between the two wires ends that connected to
the plot connector (the green connector that connected
to the Base Station).
- In case of signal interference call the service for help;
D
- The mower contacts do not touch the Docking
Station contacts
- Make sure that both mower drive wheels are leveled
with the Docking Station base (if necessary fill the area
underneath the drive wheels with dirt)
Docking problem
- The mower or Docking Station contacts are
dirty
- Clean the contacts with a brush or piece of cloth
- Charging is not detected, although there is
physical contact between the mower and the
Docking Station contacts (mower is found in
the Docking Station entrance).
- Turn on the Perimeter Switch
- Confirm a good connection of the cables to the
Docking Station contacts.
- Check the Charging fuse 5A (remove the plastic cover
below the Manual Controller).
- Mower does not reach the Docking Station
within the time and distance limitations.
- Confirm the mower is operated in a docking zone.
- Confirm the mower is not slipping or stuck on its way
to the Docking Station.
Drive Overload
Cooling Wait…
- The drive motors have been working under a
severe load for too long.
- There is no need to do anything – Robomow will renew
automatically the operation, as the drive motor will cool
down.
Drive problem
- Internal failure - Contact service provider
E
- The theft guard system is activated
- Enter the correct 4-digit code. ‘Theft Guard’ can be
deactivated under ‘User Preferences’. Contact your
service provider for assistance in a lost code situation.
Enter Code
64


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow RL serie at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow RL serie in the language / languages: English as an attachment in your email.

The manual is 19,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow RL serie

Robomow RL serie User Manual - German - 84 pages

Robomow RL serie User Manual - Dutch - 84 pages

Robomow RL serie User Manual - French - 84 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info