644654
34
Zoom out
Zoom in
Previous page
1/58
Next page
33
EN
Chapter 6 –
Robomow Operation
6.1 Automac Operaon
o Once the One-Time Setup is nished, Robomow will be set to perform automatically the following cycle of
mowing operations:
- When the battery is fully charged, Robomow will automatically depart from the Base Station.
- It will mow the lawn.
- It will start searching for the Base Station, when the battery level gets low (Robomow will not mow when
it is searching for the Base Station).
- It will recharge the battery and get ready for the next scheduled operation.
- It will continue mowing until it completes the required number of mowing hours (end of a Mowing Cycle).
Note: Robomow mows the Edge of the entire lawn only on the rst mowing operation of each Mowing Cycle.
In the rest of operations Robomow mows the lawn without the Edge. When Mowing Frequency (p001 in
Section 6.4.2) is set to HIGH, Robomow will mow the Edge twice a week.
o The required mowing time for a single mowing cycle is automatically derived from the Area setting for your
lawn.
o In case the required mowing time within a mowing cycle needs to be adjusted (increased/decreased) to
achieve better mowing results, it can be done using the Mowing Hours menu – see Section 6.4.2.
o Robomow usually performs several consecutive mowing operations until it completes a full mowing cycle
required for the lawn. After completing a mowing cycle Robomow will rest until the next cycle should begin.
The interval between mowing cycles is dened by the Mowing Frequency menu see Section 6.4.2. The
default setting is to perform two complete mowing cycles per week (Medium Mowing Frequency)
o Robomow stays in the Base Station during the default Inactive Time (All day Sunday and nighttime daily
23:00 to 06:00). Inactive Time may be changed – see Section 6.4.1.3.
Note!
Robomow has the power to mow high grass. However when mowing high grass during the rst use or the rst
mowing of the season, initially you will see uneven patches of grass.
Please be patient as it may take a few days to one week to overcome and bring the lawn to an even height and
consistency.
6.2 Operang Panel
Operating Panel and buttons:
AM
Mo
Tu We Th Fr Sa Su
Days of the week
Mower is in the
Base Staon
indicator
Day and Time
seng indicator
Mowing Hours (%)
seng indicator
Inacve Time
seng indicator
Rain Sensor
Red lit constantly – Low Baery
Green blinking – Charging
Green lit constantly – Fully Charged
Baery and
Charging
indicator
User / Error messages
Area seng indicator
ok
STOP
Mowing with Edge / Le
arrow
OK to choose /
approve selecon
Mowing without Edge /
Right arrow
GO to Base (Home)
Stop (during operaon) /
Back while in the menu
Sengs
6.3 Manual Operaon
Manual Operation is used when you want to manually send the mower to mow your lawn, regardless the
Automatic Operation’s schedule.
To initiate Manual Operation, while Robomow is at the Base Station, press one of the buttons (except the STOP
button) to show the display.
If the battery is fully charged and the Automatic Operation is enabled (see Section 7.3), then the start time of the
next operation is displayed, otherwise the current day and time are displayed.
Once the display is shown, choose the operation mode you want as provided in the table below:
Operation Mode Child Lock is Off Child Lock is On
Mowing with Edge – Mowing
the edge of the entire lawn before
starting to mow the inner area of
a selected zone.
It is recommended to use this
mode once or twice a week,
depending on how fast the grass
is growing.
Press the ‘Edge before mowing’
(left arrow) button once
Press the ‘Edge before mowing’
(left arrow) button then press OK
Mowing without Edge – Mowing
only the inner area of a selected
zone without the edge.
It is recommended to use this
mode only in the rst operation of
each Mowing Cycle.
Press the ‘Mowing’ (right arrow)
button once
Press the ‘Mowing’ (right
arrow) button then press OK
Note if a Sub-Zone is dened, L1 (Main Zone) will be displayed when you choose an operating mode. Use the
arrow buttons to scroll and choose the required zone to be mowed and press OK.
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow MC800 - 2016 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow MC800 - 2016 in the language / languages: English as an attachment in your email.

The manual is 5,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robomow MC800 - 2016

Robomow MC800 - 2016 Quick start guide - English - 4 pages

Robomow MC800 - 2016 User Manual - German - 62 pages

Robomow MC800 - 2016 User Manual - Dutch - 62 pages

Robomow MC800 - 2016 User Manual - French - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info