625559
28
Zoom out
Zoom in
Previous page
1/46
Next page
NX SERIES V0913 27
English
Sliding table (g. 11)
The machine is delivered with the sliding table mounted onto it. For a good adjustment and functioning
of the sliding table, it is necessary that the machine is evenly placed in both directions by means of a
level. All adjustments and adaptations of the sliding table have been made by the factory.
To create a smooth movement of the wood or the panel, the sliding table is set at +/- 0.2 mm above de
cast iron saw table.
The sliding table can be locked in one position along the whole length. This is necessary when, for
example, sawing lengthways with the parallel fence.
The bolt is situated on the side of the sliding table (g. 11.1). Pull the bolt forward and click it in the
opening at the side of the sliding table. To unlock it, pull the bolt backwards and turn it 180°. Two
rubber stops on the lower beam of the sliding table stop the course of the sliding table. When multiple
movements back and forwards are repeated, it is possible that the ball bearing moves slightly. This will
cause some resistance when pushing the sliding table.
This can also occur if the total course of the sliding table is shortened. With a few short pushes, with
the purpose of reaching the end of the course, the position of the ball bearing can be improved.
Fig.11
Attention: cleaning and maintenance of the sliding table
It is essential to frequently blow away the accumulated shavings and dust, between the two
parts of the sliding table and the ball bearing. Push the sliding table to the end of the course
to get better access to the rails, the ball bearing and the slides of the sliding table. Repeat
this, with the sliding table moved to the other side, to be sure all shavings and dust is gone.
A normal lubricant such as WD-40 is sufficient to grease the slides of the sliding table and to
obtain good functioning.
ADJUSTMENT OF THE SLIDING TABLE (g. 12)
The alignment between the sliding table can be adjusted by means of the 2 adjustment points below
the fixed beam of the sliding table. Loosen the 2 screws (2) that hold the fixed beam on the chassis
of the machine. Loosen the 2 bolts (1) and align by moving the sliding table. After the adjustments,
tighten the 2 bolts. The adjustment of the sliding table against the cast iron saw table is made by
means of the 2 bolts (1).
1
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robland NXTZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robland NXTZ in the language / languages: English as an attachment in your email.

The manual is 1,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robland NXTZ

Robland NXTZ User Manual - German - 100 pages

Robland NXTZ User Manual - Dutch - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info