625546
29
Zoom out
Zoom in
Previous page
1/98
Next page
28 V0212 HX SERIES
English
Deutsch
Thicknesser - planer - mortiser
Warning
1 Always make sure there is no tool left in the mortising chuck before starting up the planer-
thicknesser.
2 Check very carefully whether the planer knives are well positioned and fastened. If this is not the
case, they will come off when the machine is started and this could lead to serious injuries for the
operator and damage the machine.
Changing and setting of the planer knives (g. 24)
1 Unlock the bolts (1) in the jib strip and remove the planer knives
2 Remove the 3 jib strips and clean the grooves inside the planer arbor. Make sure the little springs
(2) underneath the knives do not stay blocked inside their seats in the arbor
3 Never use planer knives which have less than 20 mm height
4 Put the cleaned planer knife (3) into the groove with the adjustment gauge (X428)
5 Tighten the bolts from the middle of the arbour to the outside
6 Do a trial run of the machine and then tighten the knives again.
Adjustment of the planer tables (g. 25)
1 The out feed planer table has to be set at exactly the same height as the planer knives.
2 A simple way of checking the correct height of this out feed table is to put a 100 % straight piece
of wood onto the out feed table, just above the planer knives. Both tables have a clamp handle
(1) and an adjustment knob (2).
3 To adjust the table in height, use the adjustment knob (2)
4 During this adjustment, turn the planer arbor by hand and see if the planer knife touches the
piece of wood.
5 After the adjustment in height the table has to be blocked again.
6 The chip removal is adjusted through the height of the in feed table and can be max. 4 mm.
7 After the adjustment, block the table again.
8 The opening of the table happens by means of loosening the handles and opening the tables.
9 The tables are automatically clamped when they are open for planning. To undo the clamping,
simply pull the knob (3) down and close the table.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robland HX310 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robland HX310 in the language / languages: English, German as an attachment in your email.

The manual is 5,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robland HX310

Robland HX310 User Manual - Dutch - 48 pages

Robland HX310 User Manual - Dutch, French - 102 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info