Manual Robland E300 (page 12 of 65) (English, German)

625575

Zoom out

Zoom in

1/65

E300 / E 2800 V0913 11

EnglishDeutsch

Mounting of the E-2800 sliding table on

the machine (Fig.7 bis)

The position of the sliding table relative to the machine is factory set and normally needs no further

adjustments.

Simply put the table onto the frame with the two lateral adjusment bolts in the two lugs placed at

each side of the frame.

These lateral adjusment bolts are also factory set and normally need no adjustment.

Now place the 4 big Allen bolts into the lower section of the sliding table: ensure the table does not

ﬂip over when sliding away the upper section of the sliding table.

These 4 bolts need to be tightened with a Torque wrench at 80 Nm (8 kgs.)

This is best done by an experienced Robland technician thus avoiding serious problems with the loss

of warranty on the sliding table as a result.

To ensure a clean and neat cutting result the table has to be given a free cut left: the sliding table

does not run exactly parallel to the saw blade, it runs away from the back teeth by a fraction of a

millimeter.

All saw blades vibrate to some extent: they ﬂutter less at the front where the cutting teeth are held

stable by the material than at the back.

If the table were set absolutely parallel to the saw blade, the back teeth could retouch the material

and spoil the clean cut achieved by the front teeth.

As the back teeth are ascending they could cause chip-out on the top surface of the laminated

boards

(back cutting).

To correct the free cut, loosen slightly the vertical 4 big Allen bolts and loosen the nut of the lateral

adjustment bolt at the far end of the sliding table. Adjust, and re-lock the stop bolt at the end you’re

adjusting.

Recheck the free cut if OK and make ﬁnal test cut.

Make sure the 4 big Allen bolts are well tightened and locked at 80 Nm.

Fig.7 bis

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Robland E300 in the language / languages: English, German as an attachment in your email.

The manual is 3,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robland E300

Robland E300 User Manual - Dutch, French - 65 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Robland E300 Manual

Product: