747912

Robbe Futaba T6EX Manual

14
Zoom out
Zoom in
Previous page
1/38
Next page
14
PROGRAMMING THE 6EX-2.4GHz RADIO
Anytime you wish to view or change any of the current settings in the transmitter, the programming mode must first be
entered by, of course, turning on the power, then by pressing the “MODE” and “SELECT” keys simultaneously and holding
them down for one second. Once in the program the MODE key will be used to scroll through each of the functions (Model
type ACRO: model select/ data reset/ model type select/ modulation select/ trainer/ model name, reversing, dual rates/
exponentials, end point adjustments, trim, programmable mix 1, programmable mix 2, flaperon mixing, flap trim, v-tail mixing,
elevon mixing, and failsafe Model type HELI: model select/ data reset/ model type select/ modulation select/ model name,
reversing, dual rates/ exponentials, end point adjustments, trim, normal throttle curve, normal pitch curve, idle-up throttle
curve, idle-up pitch curve, throttle hold, revolution mixing, gyro sensitivity, swash-throttle mixing/ swashplate types, and
failsafe) and the SELECT key will be used to view the settings within the function. When a data change is actually required the
“DATA INPUT” lever will be used to increase or decrease the value of the item displayed, thus making the change.
You can return to the home screen (where the model name and battery voltage is displayed) by pressing the MODE and
SELECT keys simultaneously and holding them down for one second.
Note: The functions are listed and described in the order that they appear in the transmitter. Read all the way through the
programming instructions before setting up your model (if you won’t be using any of the mixing functions for a while you
can read those instructions when ready). Refer to the FLOW CHART on page 31(ACRO) or page 32(HELI) as well.
Model Select
/ Data Reset / Model Type Select / Modulation Select / Trainer / Model Name
MODL Model select function
To select model memory:
1. Access the Model Select function in the programming mode (by pressing the MODE and
SELECT keys simultaneously and holding them down for one second). The number for the
current, active model will be blinking.
2. To activate a different model memory press the DATA INPUT lever and hold it down for 0.5
seconds until the desired model number appears.
3. Now the model has been selected. All programming inputs from this point forward will affect
only the model number on the screen (until another model number is selected).
REST Data reset function
All the data for any model memory can be reset to the original factory defaults. Often this function is done to get a “fresh start”
and clear the memory before inputting new model settings.
To reset data:
1. Access the Model Select function in the programming mode (by pressing the MODE and
SELECT keys simultaneously and holding them down for one second). To select the model
memory you wish to reset press the DATA INPUT lever and hold it down for 0.5 seconds
until the desired model number appears.
2. Once the desired model number is displayed on the screen, press the SELECT key. A
“REST” will appear on the screen.
3. Push DATA INPUT upward or downward for about 2 seconds to clear and reset the memory.
“CLR” blinks first, and then it stops blinking with a sound. Now the model data is reset to the
initial setting that is the default value set at the factory.
The existing modulation and swashplate type settings are not reset. If the power switch is turned off while reset is underway,
the data may not be reset.
CAUTION: Resetting the current model memory will permanently erase ALL programming information for that model. The
data cannot be recovered (unless you recorded it on a Model Data Recording Sheet in the back of this manual). Do not reset
the model unless you are certain you want to clear-out that memory and start from scratch.
When actually setting up a model you should have the model in front of you with the power on so you can actually see the
effects of your programming inputs and measure the control throws.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe Futaba T6EX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe Futaba T6EX in the language / languages: English as an attachment in your email.

The manual is 2,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info