520094
25
Zoom out
Zoom in
Previous page
1/105
Next page
Select menus
FX-40
25
12.3 MODEL MENU (FIXED-WING AIRCRAFT)
This menu contains the settings specific to each model type for each
model memory, especially mixer functions. The Select menu varies
accor
ding to the model type you have selected:
Servo Monitor = Servo travel display
Condition Select = Flight mode select
AFR (D/R) = Transmitter control travel settings, Dual Rates
Prog. Mixes = Ten freely programmable mixers
AIL Differential = Aileron differential
Flap Setting = Mixer setting, brake -> flap
AIL to Camber FLP = Aileron -> flap mixer
AIL to Brake FLP = Aileron -> brake flap mixer
AIL to RUD = Aileron -> rudder mixer
Airbrake to ELE = Airbrake -> elevator mixer
Camber Mix = Flap -> brake flap mixer
ELE to Camber = Elevator -> flap / brake flap mixer
Camber FLP to ELE = Flap / brake flap -> elevator mixer
RUD to Ail = Rudder-> aileron mixer
RUD to ELE = Rudder -> elevator mixer
Snap Roll = Snap roll settings
Butterfly = Butterfly (Crow) settings
Gyro = Gyro settings
Fuel Mixture = Carburator mixture adjust
Multi Engine = Mixer for multi-engine models
Trim mix 1 + 2 = Trim mixers 1 + 2
Motor = Motor settings
V-tail = V-tail mixer
Ailevator = Separate elevators (aileron function)
Winglet = Winglet mixer, flying wings
MODEL MENU (HELICOPTER)
Servo monitor = Servo travel display
Condition Select
= Flight mode select
AFR (D/R) = T
ransmitter control travel settings, Dual Rates
Prog. Mixes = Ten freely programmable mixers
PIT Curve = Collective pitch curve settings
THR Curve = Throttle curve settings
Acceleration = Acceleration, throttle / coll. pitch function
Throttle Hold = Auto-rotation settings
Swash Mix = Swashplate mixer
Throttle Mix = Throttle mixer
PIT to Needle = Coll. pitch -> needle valve mixer
PIT to RUD = REVO mix (tail rotor mixer)
Fuel Mixture = Carburator mixture settings
Gyro = Gyro mixer
Governor = RPM governor (regulator)
12. SUMMARY OF SELECT MENUS
12.1 SYSTEM MENU
This menu is used to adjust transmitter settings which apply to
all models, i.e. they ar
e non model memory-specific.
T
rainer = Trainer mode settings
Display = Contrast / backlighting, transmitter power-off
Date / Time = Calendar, date and time settings
User name = User name and PIN
Switch = Switch type and position settings
HW/Setting = Hardware transmitter control reverse
Primary stick response time and dead-
band
Stick mode select, throttle left / right
Information = Software version, memory capacity and
language switch (German / English)
12.2 Linkage MENU
This is where all the model’s basic settings are adjusted, and
picture and sound files ar
e linked to each model memory
.
Servo Monitor = Servo travel display
Model Select = Model memory select
Model Type = Model type select
Picture = Picture link
Sound = Speech output link
Frequency = Frequency / modulation select
Function = Transmitter control select,
channel sequence
Sub-Trim = Servo centre offset
Servo Reverse = Servo travel direction reverse
Fail Safe = Servo position if signal fails
End-Point (ATV) = Servo travel adjust
Throttle Cut = Motor cut function
Idle Down = Second throttle idle position
Timer = Stopwatch adjust
Dial Monitor = Display of trimmer / adjustor
positions
Data Reset = Reset data
The menu for the Helicopter model type with electronic swash-
plate mixing (HR3, H4) also includes a Swashplate menu,
(swash) where you can define the neutral point of the collecti-
ve pitch function and set the swashplate travel.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe Futaba FX-40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe Futaba FX-40 in the language / languages: English as an attachment in your email.

The manual is 3,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robbe Futaba FX-40

Robbe Futaba FX-40 User Manual - German - 105 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info