520094
20
Zoom out
Zoom in
Previous page
1/105
Next page
Switching the transmitter on
Changing the frequency
channel
FX-40
7. SWITCHING THE TRANSMITTER ON / OFF
Locate the switch on the transmitter marked “Power”, and slide it
to the right.
After the loading and initialisation phase (monitor LED flashes yel-
low) the scr
een displays the spot frequency confirm field, and the
monitor LED flashes pink.
The request to check the spot frequency appears every time you
switch the transmitter on.
If the transmitter is set to the correct channel, and you wish to trans-
mit an RF signal, press the “Yes” button.
The colour of the monitor LED now changes to a continuous green,
indicating that an RF signal is being broadcast.
If you press “No”, the display switches to the Start menu, and no
RF signal is transmitted.
In this case you can now carry out adjustments without radiating
an RF signal, or change the spot frequency, so that the transmitter
starts on the correct channel next time you switch it on.
NOTE:
If the transmitter was last switched on more than four hours previous-
ly, the initialisation phase will take a little longer (cold start). If a D/P card
is fitted this will also pr
olong the start phase slightly
, as the transmitter
must first read all the files on the card.
CAUTION:
Never switch the transmitter off during the initialisation phase
(monitor LED flashes yellow), as this could corrupt the set-
tings.
SWITCHING THE TRANSMITTER OFF
Move the “Power” switch on the transmitter to the left.
This action cuts of
f RF transmission, and causes the data in
the working memory to be written to the transmitter’s inter-
nal memory or the D/P card. During this process the moni-
tor LED flashes yellow, and the screen displays the mes-
sage “Storing model data”.
Switching the transmitter on again during the power-off / data
storing process could also cause damage to data, so the
transmitter ignores your action if you do this.
LANGUAGE SWITCH ENGLISH GERMAN
If your transmitter is set to German screen displays and you
wish to switch to English, please follow this procedure:
Switch the transmitter on; the query “T
ransmit?” appears
on the screen
Press the “No” button
Call up the System menu by pressing the “S1” button, then
press the “Information” button.
At bottom left press the “German” button in the Language
field, then select “English”, and switch the transmitter off.
Switch the transmitter on again, and the screen displays will
now be in English.
20
8. CHANGING THE SPOT FREQUENCY
The system incorporates a DD Synthesizer system which
generates the spot frequencies. The channel is selected at the
transmitter by softwar
e, and information on the selected chan-
nel is sent to the receiver using the Wireless Frequency Setting
System (WFSS); the receiver responds by switching to the
same channel.
The new spot frequency is stored in the receiver - even when
it is switched off - until the channel is changed again.
Press the Spot frequency field in the Start menu
The screen displays the “Frequency” setup menu.
Check that the set receiver number (label on the back of
the receiver) is entered correctly, because it is only possi-
ble to transmit a spot frequency if the appropriate receiver
number is transmitted at the same time.
Press the Spot frequency button, and the screen displays
a three-page table of channels, showing all the frequencies
approved for use in Europe. Select a channel which is per-
mitted in the country in which you wish to operate the
model. A summary of the frequencies approved for use in
European countries is supplied with the system.
Press the “Enter” button to confirm the new spot frequen-
cy you have chosen. (Press “Return” if you wish to inter-
rupt this function without making a change.)
Frequenzkanalwahl
Frequenzbandwahl
Modulationsartwahl
Empfängernummer
Nr. für 2. Empfänger
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe Futaba FX-40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe Futaba FX-40 in the language / languages: English as an attachment in your email.

The manual is 3,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robbe Futaba FX-40

Robbe Futaba FX-40 User Manual - German - 105 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info