520097

Robbe Futaba FF-10 Manual

98
Zoom out
Zoom in
Previous page
1/119
Next page
98
GOAL of EXAMPLE: STEPS: INPUTS:
Set up Normal Flight Condition
Throttle/Collective Pitch Curves and
Revo.
Base point: Adjust base point of throttle
curve until engine idles reliably on
ground. Adjust base point of collective
pitch curve to achieve -4 degrees of
blade pitch. Apply throttle until the
model sits ‘light’ on its skids. Adjust
base point of
REVO
. until model does not
rotate its nose at all.
Open the
THR-CURV/NOR
function.
Adjust the fi rst point. (Ex:
5%
.)
for 1 second.
(If
ADVANCE
, again.)
C
to
THR-CURV/NOR
.
C
to
POINT-1
.
to
5%
.
Open the
PIT-CURV/NOR
function.
Adjust the fi rst point. (Ex:
8%
.)
C
to
PIT-CURV/NOR
.
C
to
POINT-1
.
to
8%
.
Open the
REVO. /NORM
function.
Adjust the fi rst point. (Ex:
4%
.)
C
to
REVO. /NORM
.
C
to
MIX
.
to
ON
.
C
to
POINT-1
.
to
4%
.
Hover point: Adjust collective pitch
curve to +5 degrees. Ease heli into a
hover. Land/shut engine off. Adjust
throttle curves and rudder trim. Repeat
until model hovers smoothly at half
throttle. Rapidly apply throttle from 1/4
to 1/2 stick. Adjust
REVO
. points 2 and 3
until the model does not rotate its nose
up on throttle application.
Adjust
THR-CURV/NOR
. Repeat above as needed.
Adjust
PIT-CURV/NOR
. Repeat above as needed.
Adjust
REVO. /NORM
. Repeat above as needed.
High point: Adjust collective pitch
curve to +8 to +10 degrees. From hover,
throttle up rapidly. If engine bogs,
increase the throttle curve. If engine
over-revs, increase the collective pitch
curve at points 6 or 7. Apply full throttle
while hovering, then descend back to
hover. Adjust
REVO
. until the nose does
not change heading.
Adjust
THR-CURV/NOR
. Repeat above as needed.
Adjust
PIT-CURV/NOR
. Repeat above as needed.
Adjust
REVO. /NORM
. Repeat above as needed.
Where next?
GYRO
function: see p. 107.
Adjust
HOV-THR
and
HOV-PIT
if needed: see p. 104.
Setting up Throttle Hold: see p. 99.
Setting up idle-ups 1, 2 and 3: Throttle and collective pitch curves and revo.
mixing (
THR-CURVE, PIT-CURVE, REVO. MIX
): see p. 101.
GOVERNOR
function: see p. 108.
D/R
,
EXP
: see p. 42.
THROTTLE CUT:
The
THROTTLE-CUT
function is used to kill the engine at the end of a flight.
The engine can be stopped with one touch of any switch, eliminating the need
to move the trim to kill the engine and then readjust prior to each fl ight. The
helicopter
THROTTLE-CUT
includes an ON/OFF throttle position (normally a
little above idle). You must move the THROTTLE STICK back below the set
point before the
THROTTLE-CUT
function can be reset, to avoid sudden engine
acceleration. For a detailed example of throttle cut setup, see
ACRO
p. 41.
Note: Be sure to add the step of setting a trigger point by cursoring to
THRO
, then putting the THROTTLE STICK in the
desired position and pressing and holding the dial for one second. Notice that this function cannot be reversed to trigger
only above the stick point.
… 98 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe Futaba FF-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe Futaba FF-10 in the language / languages: English as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robbe Futaba FF-10

Robbe Futaba FF-10 User Manual - German - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info