520097
62
Zoom out
Zoom in
Previous page
1/119
Next page
62
ELEV-FLAP
mixing (
ACRO
/
GLID
):
ELEV-FLAP
mixing is the rst pre-programmed mix we'll cover. This mix makes
the aps drop or rise whenever the ELEVATOR STICK is moved. It is most
commonly used to make tighter pylon turns or squarer corners in maneuvers. In
most cases, the aps droop (are lowered) when up elevator is commanded.
Adjustability:
Rate: -100% (full up ap) to +100 (full down ap), with a default of +50%
(one-half of the ap range is achieved
when the ELEVATOR STICK is pulled
to provide full up elevator.)
Switch: fully assignable. Also LOGIC SW (Lsw1 to 3) may be assigned. Set up
LOGIC SW
: See p. 38.
*IF you set it to
NULL
, the mix does not work. (
ACRO
)
Range (
GLID
): The range that mixing does not work near neutral of an elevator
stick can be set up.
Hold the stick to the desired point (upper or lower side) , then press DIAL and
hold one second to set the range.
Condition (
GLID
): The separate
ELEV-FLAP
settings for each condition can be set.
(
ACRO
)
(
GLID
)
GOAL of EXAMPLE: STEPS: INPUTS:
Activate
ELEV-FLAP
mixing. Adjust flap
travel to
0%
aps with negative elevator
(push) and
45%
flaps with positive
elevator.
Open the
ELEV-FLAP
function.
for 1 second.
(If
BASIC
, again.)
C
to
ELEV-FLAP
.
Activate the function.
C
to
MIX
. to
ACT
.
Adjust the travels as needed.
(Ex:
0%
,to
45%
.)
C
to
RATE
.
ELEVATOR STICK. to
0%
.
ELEVATOR STICK. to
45%
.
Close menu.
Where next? Adjust aperons' ap travel available (
FLAPERON
): see p. 52.
Set up
AIRBRAKE
(crow/butter y): see p. 63.
Set up programmable mixes (ex:
FLAP-ELEVATOR
): see p. 68.
View additional setups on the internet: www.futaba-rc.com\faq\.
62


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe Futaba FF-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe Futaba FF-10 in the language / languages: English as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robbe Futaba FF-10

Robbe Futaba FF-10 User Manual - German - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info