520097
17
Zoom out
Zoom in
Previous page
1/119
Next page
17
Changing Modes (
TX SETTING
):
Hold down MODE and END keys while turning on the transmitter to call
TX SETTING
menu.
Stick Mode: The screen reads "
STK-MODE
". Change this to the correct mode. Note that this will
NOT change the throttle and elevator rachets, etc. Those are mechanical changes that must be
done by a service center.
Throttle Reverse:
THR-REV
is a special function that reverses the entire throttle control, including moving the trim
functionality to the Stick’s upper half. To use
THR-REV
, CURSOR DOWN to
THR-REV
and turn the DIAL to
REV
. Turn the
transmitter off and back on. This change affects all models in the radio.
Display language: can be selected the display language of the function name, etc. in each function menu. The screen reads
"
LANGUAGE
". Change this to the desired language.
TM-10 Area Selection (Frequency Range) (TM-10 module only):
The TM-10 transmitter module has been designed to function in many countries. If you will be utilizing this module in a
country other than France, please make sure that
TM10-MODE
is set to "
GENERAL
". If, however, this module will be utilized
in France, it must be set to "
FRANCE
".
[Note] While changing the above modes, the transmitter transmits in
PPM
mode even if the set-up mode is
PCM
mode and
the RF power is turned off when using a TM-10 module.
Power Down mode (
TM10 POWER MODE
) (TM-10 module only):
We have installed a special "Power Down Mode" for doing a ground range check. Hold down
DIAL while turning on the transmitter to call
TM10 POWER MODE
menu.
Power Down Mode: To activate the "Power Down Mode" press DIAL and the home screen will appear. During this mode,
the RF power is reduced so the range test can be performed. In addition, when this mode is activated the blue LED on the
front of the transmitter starts blinking and the transmitter gives users a warning with a beep sound every 3 seconds.
The "Power Down Mode" continues for 90 seconds and after that the power will go back to the normal level. To exit the
"Power Down Mode" before the 90 seconds, press DIAL again. This mode is available 1 time only so if you need to re-use
this function the transmitter power must be cycled. NEVER start ying when the "Power Down Mode" is active.
Power Off Mode: To use the RF power off mode, CURSOR DOWN to
OFF
and press DIAL. During this mode, the RF
power is turned off. The blue LED on the front of the transmitter is turn off.
CAMPac Initializing Method and Data Conversion (T9C/T9CS to T10C):
Insertion of a new CAMPac or a CAMPac containing data of a different transmitter type will
open
EXT-MEMORY
menu after turning the transmitter on.
To initialize the CAMPac, CURSOR DOWN to "Yes" and press DIAL and the check display of "OK?" will appear. Press
DIAL again, the initializing of the CAMPac will strat.
To convert the CAMPac data from T9C/T9CS to T10C, select to "No" by CURSOR lever and then press DIAL and the
home screen will appear. See p.30 for the conversion method.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe Futaba FF-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe Futaba FF-10 in the language / languages: English as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robbe Futaba FF-10

Robbe Futaba FF-10 User Manual - German - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info