592102
4
Zoom out
Zoom in
Previous page
1/9
Next page
EnglishEnglish 3 4
Before switching on make sure that the voltage of your electricity supply is the same as
that indicated on the rating plate.
For your own safety read the following instructions carefully before attempting to connect
this unit to the mains.
MAINS (AC) OPERATION
This unit is designed to operate on AC 230V 50Hz current only. Connecting it to other
power sources may damage the unit.
CAUTION
To prevent electric shock disconnect from the mains before removing cover. No user
serviceable parts inside. Refer servicing to qualified service personnel.
SAFETYPRECAUTION
This symbol means that this unit is double insulated. An earth connection is not
required.
POWER SUPPLY
Remove the stereo carefully from the box, retaining the packaging for future use (servicing).
AC POWER OPERATION
Connect the plug to a mains power inlet 230V AC ~ 50 Hz.
Do not allow this unit to be exposed to rain or moisture.
Mains Supply: 230V 50Hz - AC only
The belt and turntable platter have been installed properly at factory, but the belt may be
loose during transportation. If so, the following procedures will be taken for belt installation
by yourself.
CONNECTING TO POWER ASSEMBLING
Auto Return Reset:
Always do the reset for Auto Return once you move this product. The mechanism of Auto
Return will rotate irregularly when moving and it will cause the malfunction of Auto Return.
The following steps will reset the mechanism to normal.
1. Place a record on the platter and play it.
2. Manually lever the tone arm and place it to the blank part of the end of the record.
3. The mechanism of Auto Return function will be adjusted properly and the tone arm
A. Remove the rubber mat from the turntable platter and the E ring from the
turntable shaft, then release the turntable platter from the shaft
B. Put the drive belt on the inner rim of the turntable platter and pull it through the
hole
C. Hold the belt with your fingers and place the belt onto the motor pulley as shown
in the drawing "Fig. 1".
D. Clip the E ring on the shaft and place the rubber mat onto the turntable
platter.
will automatically return to the arm rest.
Caution:
1. Make sure that the drive belt is not twisted or distorted.
2. Avoid oil. Oil splashes will make the belt slippery.
Fig. 1
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roadstar TTL-850USDE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roadstar TTL-850USDE in the language / languages: English, German as an attachment in your email.

The manual is 1,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info