592294

Roadstar CLR-2560 Manual

4
Zoom out
Zoom in
Previous page
1/20
Next page
English English
POWER SUPPLY
This unit operates from a main supply of 230V ~ 50Hz. Connect the AC power
cord to the AC household main outlet. Ensure that the voltage is as indicated
on the rating plate on the rear of the unit.
Battery Back-up Power Failure Protection
This radio has a battery back up circuit that will keep the correct time and
alarm settings in the event of a temporary power interruption.
Install a 9-volt battery (type 6F 22/006P), not included, into the battery
compartment located on the bottom of the unit.
Note: We recommend an alkaline battery for longer usable life. Change the
battery every 9 to 12 months for best result and avoid possible battery
leakage.
If power is temporarily interrupted the display will blink and the radio will not
play. However, the battery back-up circuit will continue to maintain the clock
and alarm settings. When power is restored the clock will display the correct
time and alarm settings, and no adjustment is necessary.
Note: If power is interrupted and there is no battery in the compartment or
the battery is exhausted. The time and alarm settings will be lost.
When power is restored the clock will begin to flash indicating that the
time and alarm settings must be corrected.
SETTING THE CORRECT TIME
1. Set the FUNCTION Selector (1) to the OFF position.
2. Press and keep pressed the TIME SET Button (14), then press the
HOUR button (9) to advance hour, press MINUTE button (13) until the
correct time is displayed.
SETTING THE WAKE UP TIME
1. Set the FUNCTION Selector (1) to the OFF position.
2. Set the alarm time by following this procedure:
3. Press and hold the ALARM SET Button (8).
4. Press the HOUR Button (9) to advance hour, press MINUTEbutton (13)
until the desired alarm time is displayed.
5. Release the ALARM SET Button (8).
6. To check the correct alarm time is set, press the ALARM SET Button (8).
WAKE TO BUZZER ALARM
1. Set the alarm time as shown above.
2. Set the Function Selector (1) to the AUTO position.
“”will appear on the left lower side of the display.
3. Turn the VOLUME Control to the desired level.
4. To switch off the alarm either press the ALARM SET (8) or set the
FUNCTION Selector (1) to the OFF position.
WAKE TO THE RADIO
1. Set the alarm time as shown above.
2. Set the FUNCTION Selector (1) to the ON position.
3. Set the FM/AUX Selector (11) to FM, and follow the procedure in
LISTENING TO THE RADIO to tune the radio to a station.
4. Set the VOLUME Control (12) to a level you feel will wake you.
5. Set the FUNCTION Selector (1) to the AUTO position. “”will appear
on the left lower side of the display.
6. To switch off the alarm either press the ALARM SET (8) or ALARM OFF
Buttons (17), or set the FUNCTION Selector (1) to the OFF position.
LISTENING TO THE RADIO
1. Set the FUNCTION Selector (1) to the ON position.
3 4
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roadstar CLR-2560 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roadstar CLR-2560 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info