471677
4
Zoom out
Zoom in
Previous page
1/27
Next page
English English
POWER SUPPLY
This unit operates from a main supply of 230V ~ 50Hz. Connect the AC
power cord to the AC household main outlet. Ensure that the voltage
is as indicated on the rating plate on the rear of the unit.
Battery Back-up Power Failure Protection
This radio has a battery back up circuit that will keep the correct time
and alarm settings in the event of a temporary power interruption.
Install a 9-volt battery (type 6F 22/006P), not included, into the battery
compartment located on the bottom of the unit.
Note: We recommend an alkaline battery for longer usable life.
Change the battery every 9 to 12 months for best result and avoid
possible battery leakage.
If power is temporarily interrupted the display will blink and the radio
will not play. However, the battery back-up circuit will continue to
maintain the clock and alarm settings. When power is restored the clock
will display the correct time and alarm settings, and no adjustment is
necessary.
Note: If power is interrupted and there is no battery in the compartment
or the battery is exhausted. The time and alarm settings will be
lost. When power is restored the clock will begin to flash
indicating that the time and alarm settings must be corrected.
CLOCK
1. Set the ON/OFF/AUTO switch (1) to 'OFF' connect the Main Cord
to the power supply. The clock display will flash on and off
indicating a power interruption and that the display time is
incorrect.
2. To set the correct time, press the TIME SET button (6) and MINUTE
SET button (10), or HOUR SET button (9), together, until the correct
time is displayed.
3. Open the Clock Battery Compartment door and fit a 9V battery. The
purpose of this battery is to store the information relating to alarm
time. And to keep the clock functioning in the event of disconnection
from the mains supply or power interrruption. Should this occur. The
clock will continue to keep time, but will not display.
NOTE: THE LED DIGITAL CLOCK AND THE PROJECTION
CLOCK MUST BE SET SEPARATELY
TIME SETTING FOR PROJECTION
- Switch the projection switch to the 'ON' position.
- To preset the HOURS, press simultaneously the HOUR BUTTON
(21) and the TIME BUTTON (20), keep them depressed until the
hour digits to be preset are displayed.
- To preset the MINUTES, press simultaneously the MINUTE
BUTTON (22) and the TIME BUTTON (20). Keep them depressed
34
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roadstar CLR-2495P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roadstar CLR-2495P in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info