Manual Ritter Vertico 7 (page 18 of 103) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish)

713270

Zoom out

Zoom in

1/103

– Tall, narrow containers are

more suitable than at, wide

ones.

– If using a coated container,

take care not to damage the

coating during blending.

To switch it on, rst press and

hold down the unlock button (7).

Then, within 2 seconds, press the

power button (8).

• Keep the unlock button

pressed during operation.

The hand blender begins to oper-

ate at the highest speed setting.

The LEDs on the LED display (6)

light up (the number that light up

depends on the current battery

level).

Info:

To prevent the hand blender

from overloading, the appliance

will switch o automatically if it

becomes overheated, if a blade

becomes jammed or if the appli-

ance is operated continuously

for more than 4 minutes. After

it switches o, all LEDs ash

slowly. You can then switch the

blender on again and continue

using it.

• Briey press the power button

again to adjust the speed if

necessary.

This reduces the speed.

Info:

The next speed setting after the

lowest speed setting is the high-

est speed setting.

• Release the unlock button to

switch the appliance o.

Displaying the current battery

level

• Briey press the unlock but-

ton (7).

The number of LEDs that light up

indicates the current battery level.

English

CLEANING

CAUTION, risk of injury:

– Keep your ngers away from

the buttons to prevent the

appliance from switching on

accidentally.

– The blades on the attach-

ments are very sharp! Never

touch these blades with your

bare hands.

To prevent the accumulation

of food residue, clean the

blender (1) thoroughly after each

use:

• Immerse the blender shaft (3)

of the hand blender in the blender

cup (14) or another container

lled with warm water and

detergent.

• Switch the hand blender on.

Allow it to operate for a short

period in the detergent solution.

• Fill the blender cup or con-

tainer with clean, clear water and

allow the hand blender to operate

in the water for a short period.

• To ensure that all food residue

is removed, detach the blender

attachment (see "Connecting/

replacing an attachment") and

clean it.

• Use a damp cloth to wipe

down the motor unit (2), blender

shaft and charging station (13) if

necessary.

NOTE, risk of damage to the

hand blender:

– Do not use any scouring

agents, abrasive cleansers,

sponges with rough surfaces

or hard brushes.

– The hand blender is not

suitable for washing in a

dishwasher.

– Do not leave the blender

shaft (3) sitting in liquid for a

long time, as this may cause

discolouration.

• Dry all parts that you have

washed.

CHARGING THE BATTERY

If the blender (1) is switched on,

the number of LEDs that light up

on the LED display (6) indicates

the current battery level. LED 1

ashes slowly to indicate that the

battery is dead.

Info:

Do not switch the blender on if

the battery is dead. Otherwise,

the battery may be damaged.

Hook the hand blender (13)

into the charging station by

positioning it at an incline and

then swivelling it into an upright

position.

The LEDs on the LED display

ash to indicate that the hand

blender is correctly connected to

the charging station. The number

of ashing LEDs indicates the

current battery level.

Once the battery is fully loaded,

all LEDs go out.

STORAGE

Keep the appliance and the

accessories out of the reach of

children. If storing the appli-

ance for a longer period of time

(without use), ensure that the

battery is fully charged rst

(see "CHARGING THE BAT-

TERY"). Otherwise, the battery

may be damaged.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ritter Vertico 7 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,29 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ritter Vertico 7 Manual

Product: