Manual Ritter AES 62 SR (page 21 of 78) (English, German, Dutch, French, Italian, Polish, Spanish, Norwegian)

544571

Zoom out

Zoom in

1/78

Assembly and installation

The last few pages of these

operating instructions contain

drawings with assembly and

installation dimensions.

Please note that the installation

dimensions differ depending on

the appliance version ("SR" or

"SL") (Figs 3)!

Safety instructions

– Assembly must be performed

by qualied personnel only.

ritterwerk will not be held

liable for the consequences of

any improper and/or incorrect

assembly.

– The mains cable must be

designed such that the

appliance can be swivelled

fully in without jamming the

appliance. The mains cable

must be routed straight from

the installation system to the

socket that is to be mounted

in the oor cabinet.

– Remove the mains plug from

the socket before assembly.

Installation conditions

Body width: ............min. 450 mm

Clearance height for drawer

base / crossbeam:

– without baseplate: .......75 mm

– with baseplate: ............83 mm

Clearance for drawer for worktop

front edge / inner edge and

drawer cover: .................365 mm

(Without mounted nger protec-

tor and left-over holder)

Clearance for width (usable)

Drawer base: .................335 mm

Appliance width: ............345 mm

The drawer base should be at

least 16 mm thick.

For a 45 cm body width, the

inclined formation of the side

frames could mean that the

width clearance (usable) of the

drawer base is a few millime-

tres too small. Mounting it on to

baseplates (15, Fig. 1) enables

up to 4 mm to be gained in terms

of width.

At a nominal length of 400 mm

the drawer's roller guide should

have a static loadability of at least

40 kg.

Mounting the socket

• Mount a surface-mounted

socket in accordance with VDE /

DIN 49440, ÖVE, SEV to the rear

panel or the side of the body (see

Fig. 2).

The connection between the

socket and the mains cable

should be routed under the rear

crossbeam or the upper base and

as far up as possible in the rear

corner of the oor cabinet.

The drawer must be capable of

being slid all the way in when the

mains cable is plugged in.

Mounting multi slicer

Preparation:

• Pull the drawer out up to the

stop.

• Determine the position for the

multi slicer in accordance with the

assembly drawing (see Fig. 3).

• Position the appliance, when

folded, into the drawer (see

Fig. 3).

The distance between the front

edge of the worktop and the

completely screwed-in buffer

screw (12) should be approx.

5 mm.

• Mark the position of the front

and rear fastening brackets

determined in this manner on the

base of the drawer.

• Remove the appliance from

the drawer.

Execution:

• Drill the four holes as marked

for assembling the appliance

onto the base of the drawer.

• Mount the appliance using

four pan-head screws 3.5 x 16

(for drawer base 16 mm).

Mounting retaining brackets

• Position the retaining brack-

ets (7) and (8) as shown in

Fig. 3.

• Check the position by placing

the nger protector and the left-

over holder onto the correspond-

ing retaining bracket (Fig. 4).

• Mark the position of the holes

and then drill them.

• Mount the two retaining brack-

ets using countersunk screws

(Phillips drive) PZ 3.5 x 12 (for

drawer base 16 mm).

Adjusting appliance position

• Position the appliance as

described in INITIAL START-UP.

• Turn the buffer screw (12)

until it just makes contact with

the front edge of the worktop

(do not clamp tight!).

• Check the setting by folding

and unfolding it several times in

succession.

Note:

All dimensions in the assembly

drawings stated in mm!

English

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ritter AES 62 SR in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish, Norwegian as an attachment in your email.

The manual is 1,63 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ritter AES 62 SR Manual

Product: