744718

Rika Rikatronic 4 V1.02 Manual

4
Zoom out
Zoom in
Previous page
1/12
Next page
2. OPERATION
Heat up
Clean the grate in the firebox and the ignition support underneath from ash
and combustion residues (see CLEANING AND MAINTENANCE). Due to this
cleaning, the path for the primary air in the firebox is free, which is required
for the starting phase.
Open the firebox door and place small pieces chipboard on the bottom of
the stove.
On top of this first layer settle on other chipboards crosswise.
Put two pieces of log wood on top of it (see QUANTITY OF FUEL AT NOMINAL
LOAD).
Pull out the ignition support which is placed under the grate. Insert 2 ribs
of the firelighter with the firing head to the left in the designated recess of
ignition support.
If you have no chipboard available, use an entire block (8 ribs) to ignite the
logs.
Note
For a successful ignition process dry logs and a sufficient chimney draft
is required.
Note
The lighter must always be inserted with the firing head to the left.
Slide in the ignition support again until it locks into the stove and close the
combustion chamber door, CHECK appears on the display.
To start the automatic ignition, press and hold the function key until the
display changes to IGNIT.
Tip
Within 10 seconds, the automatic ignition can be cancelled by holding the
function key (until the time is shown again on the display).
Heat
Once a sufficiently high temperature rise has been detected after the heat-up
or refilling, the display changes to BURN and the combustion is automatically
controlled.
Reload
The optimal time to reload the stove towards the end of the burn-down phase
is indicated by a red flashing display.
The red flashing phase will appear, depending on environmental influences,
between 5-10 minutes. After reloading and closing the stove door, the display
changes to CHECK.
With sufficient temperature increase, the display changes back to BURN and
the combustion is again automatically controlled.
Note
If the display is not changing from IGNITE / CHECK to BURN within a
certain period after closing the combustion chamber door, the heating up
or reloading failed. So the required increase of the combustion chamber
temperature has not been reached. For a further heating, a new starting
process must be carried out.
ECO-mode
After the first automatic burn cycle a heating mode with lower heat output is
possible. (see QUANTITY OF FUEL AT PARTIAL LOAD)
If you press the function key after refilling (during CHECK is displayed), the
display changes to ECO and Eco-mode is active.
ECO
In this mode, the combustion with a lower amount of fuel is also controlled
optimally.
Pressing the function key or by opening / closing the firebox door the ECO
changes back to BURN and the normal regulation is active again. The Eco-
mode must be activated again after each refilling.
Burn out
If during the red flashing phase the stove is not refilled, the combustion
chamber is cooled below the necessary temperature for refilling the
combustion chamber. The set time will be displayed again.
Note
From this point, no more wood should be refilled, because the lighting of
the new wood can no longer be guaranteed. A new fire lighting must be
carried out.
4
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rika Rikatronic 4 V1.02 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rika Rikatronic 4 V1.02 in the language / languages: English as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Rika Rikatronic 4 V1.02

Rika Rikatronic 4 V1.02 User Manual - German - 12 pages

Rika Rikatronic 4 V1.02 User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info