639647
24
Zoom out
Zoom in
Previous page
1/30
Next page
Frequently Asked Questions
22
Frequently Asked Questions
4. Frequently Asked Questions
Although our instructions in this manual are of course highly brilliant ;-) we can imagine that you
run into some questions while you are printing. This section of the manual is devoted to that. Note
that you can nd much more help and support in The Ecosystem, which you can access through
creatrhs.lpfrg.com/.
This section contains the answers to the following frequently asked questions.
4.1 How can I solve the issue of the print not sticking to the bed?
4.2 What should I do when I cannot get my lament to go through the lament guiding tube?
4.3 What can I do if my lament does not come out of the extruder?
4.4 My print surface is very rough, how can I solve this?
4.5 Where do I go with my other questions?
4.1 How can I solve the issue of the print not sticking to the bed?
If your prints do not stick to the printing glass there are several steps you have to check on:
The distance between the extruder and the printing bed: If the distance is too big the layers will
not stick and when the distance is too small the extruder will scratch the previous layer causing
it to come off.
The temperature of the bed and the nozzle: Make sure they are at the right temperature for
your material.
Material Bed Temperature Nozzle Temperature
PLA 40-45 C° (when using the printing
sticker). Turn off your bed after
layer 5
210-220 C° Depending on print-
ing speed. The lower the speed the
lower the temperature.
ABS 75-80 C° (Keep your bed heat
turned on for the entire print)
230-240 C° Depending on print-
ing speed. The lower the speed the
lower the temperature.
(For all recommended settings, please visit: creatrhs.lpfrg.com)
The tension of the lament drive on the l-
ament: The lament drive is located at the
back of the printer. Too much tension of the
drive gear on the lament causes small cuts
on the lament. If there is too little tension
the drive gear wheel will slip and unsuf-
cient material reaches the extruder. You
can adjust the tension by loosening or tight-
ening the knob.
If the problem persists even after you level the extruders please try to calibrate the printing glass
as well (as explained in section 1.6.)
Adjust tension with the knob
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ricoh Creatr HS - Leapfrog at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ricoh Creatr HS - Leapfrog in the language / languages: English as an attachment in your email.

The manual is 9,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ricoh Creatr HS - Leapfrog

Ricoh Creatr HS - Leapfrog User Manual - German - 30 pages

Ricoh Creatr HS - Leapfrog User Manual - Dutch - 30 pages

Ricoh Creatr HS - Leapfrog User Manual - French - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info