793453

Respekta CH3100GISA - Aluna Manual

32
Zoom out
Zoom in
Previous page
1/36
Next page
English 17. Installation Instructions for Island Cooker Hood
GB
The figures are for illustration purpose only. The shape and composition of your hood can differ.
8. Install the remaining 4 angle bars of the required overall length as an
extension to the already mounted angle bars. The overlap A (Fig. 5)
must be at least 10 cm and joined with 4 screws. Use the ea.16 M4 X
10 mm screws with nuts and washers.
9. Push the inner shaft A (Fig. 6) (chimney shaft with the smaller
diameter) with screw holes B (Fig. 6) upwards, over the angle bar
construction and over the edge of the mounting plate D (Fig. 6). Make
sure that the screw holes B line up with holes C (Fig. 6).
Then screw mount the inner shaft securely to the mounting plate A
(Fig. 2) with four 8 mm flat-head self-tapping screws.
10. Push the outer shaft A (Fig. 7) right up over the already screw
mounted inner shaft and fix with 2 S-hooks B (Fig. 7) in order that the
bottom part of the angle bar construction is accessible for the
subsequent mounting steps.
11. Mount the exhaust air connector A (Fig. 8) with ea. 4 8 mm flat-
head screws on the motor housing B (Fig. 8).
If the hood is fitted with a top glass screen, push this over the motor
housing from above so that the holes in the glass screen line up with
the screw holes C (Fig. 8) in the hood. Then fix the glass screen to the
hood with 4 screws.
12. Push the assembled hood into the angle bar construction and fix
it there with ea. 16 M4 screws (Fig. 9)
13. Mount the exhaust air hose A (Fig. 10) to the exhaust air
connector on the hood B (Fig. 10).
14. Raise the outer shaft C (Fig. 10) slightly, remove the 3 S-hooks D
(Fig. 10) and allow it to slide down on to the hood) see Fig. 11)
15. Installing the glass screen A (Fig. 12) (where applicable)
Install the glass plate last of all.
Fix the glass screen with mounting screws B (Fig. 12)
Fig. 11
Fig. 8 A
B
C
Fig. 9
Fig. 7
A
B
A
B
Fig. 10
C
D
Fig. 12
A
B
Fig. 6
AB
C
D
fi1200330TNM 12
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Respekta CH3100GISA - Aluna at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Respekta CH3100GISA - Aluna in the language / languages: English, German as an attachment in your email.

The manual is 1.64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info