613882

Renusol ConSole Manual

5
Zoom out
Zoom in
Previous page
1/8
Next page
2.
3.
Renusol ConSole · EN · 04/2011 — 5
A
h
B
ASSEMBLY PREPARATION
Calculating the amount of ballast for the
ConSole
The wind loads acting on the ConSole re-
quire it to be weighed down with ballast.
Gravel, stones, plates and similar materials
are suitable as ballast.
The table opposite can serve as a guide for
the required ballast. These values are calcu-
lated according to DIN 1055-4:2005-03 and
Eurocode. Several years experience confirm
the reliability of the system.
The exterior module series and column re-
quire more ballast according to the table.
The values indicated prevent the ConSoles
from tipping over, sliding or being lifted-
ConSoles.
In order to ensure safety against sliding, the
coefficient of friction between the roofing
and the ConSole must be greater than 0.6 .
This can be established using a spring
scale. A ConSole filled with 100 kg of ballast
should only move from the spring scale
under a horizontal tensile force of over
60 kg.
Additional ballast
In a higher wind load zone: 30% more bal-
last per level.
When using extension rails: 10% more bal-
last.
In case of excess length of the modules on
the side:
additional ballast in proportion to the excess
length.
Calculation basis
The ballast values are calculated for wind
load zone 1 for Germany according to DIN
1055-4:2005-03 and for terrain category III:
Suburbs, industrial or commercial zones and
forests.
*The system weight is not included in the
recommended ballast values.
Recommended ballast values for ConSoles in kg in terrace systems*
A = minimum distance of the ConSolen series:
ConSole 4.1 >1.2 m
ConSole 4.2/5.2/6.2 >1.5 m
B = minimum
roof edge > 1/5 h
h = Building height
Schematic diagram of a ConSole terrace system
Distances between rows on the ConSole system
Positioning the ConSoles
Check whether the installation surface
(e.g., the roof) is enough for the additional
roof load.
The surface must be level, clean and not
too slippery. With slippery surfaces, e.g.,
with PVC roof membranes, an anti-slip mat
should be used, e.g., a building protection
mat.
Place the ConSole with the opening facing
south. A minimum distance of a fifth of the
building height "h" should be maintained
from the side of the roof. Building height 10
metres => minimum distance 2 metres.
The minimum distance between
the ConsSoles is clear from the schematic
diagram.
Filling ballast
Now fill in the correct ballast. Reference
values here are contained in the table
"Recommended ballast values" at the top
of this page.
Ballast diagrams for all ConSole types are
available on our website
www.renusol.com/download as a PDF le.
inner ConSoles
in the slipstream
circular,
non-binding
roof area
outer,
wind-exposed
ConSoles
Roof edge
Building height
Up to 8 meters Up to 12 meters Up to 16 meters
interior exterior interior exterior interior exterior
ConSole 4.1 62 99 73 115 82 128
ConSole 4.2 58 94 68 110 77 122
ConSole 5.2 63 106 75 123 84 137
ConSole 6.2 83 134 98 156 110 173
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Renusol ConSole at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Renusol ConSole in the language / languages: English as an attachment in your email.

The manual is 1,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info