796998

Renkforce WS-WN530HP3-A Manual

5
Zoom out
Zoom in
Previous page
1/12
Next page
Operation
a) Connection
PoE converter
• Connect the PoE IN connection (4) on the device
to the (A1) connection on the PoE converter
with a CAT5 LAN cable.
• Connect the LAN DATA IN (A2) connection on
the PoE converter to the output connection (LAN
port) on your router.
• Plug the low-voltage plug of the power adapter
into the low-voltage input DC 24 V (A3) on the
PoE converter and connect the power adapter to
a standard mains socket.
• Press the ON/OFF (A4) button to switch the PoE
converter on.
• Press the ON/OFF button to switch the WLAN
AP on.
• Press the ON/OFF button to switch the PoE con-
verter off.
• Press the ON/OFF button to switch the WLAN
AP off.
Ensure that you are using an approved Ethernet (CAT) cable with RJ45 connec-
tors. The CAT cable used must be no more than 60 m in length.
b) LED indicators
• When the operating LED (3) lights up purple, the device is starting up.
• When the operating LED ashes red, the internet connection has been interrupted.
• When the operating LED lights up blue, there is a working internet connection.
c) ‘Repeater’ quick setup with WPS
• To start automatic conguration via WPS, press the Pair Reset WPS button (5) on the
device for 2 seconds. Then, release the button. The operating LED (3) starts to ash quickly.
• Press the WPS button on your WLAN router within 2 minutes. Alternatively, you can also
start WPS conguration from your router’s web interface. Please consult the operating in-
structions for your router.
• To connect a terminal device via WLAN, select your WLAN with the attached abbreviation.
The password for the WLAN is the same as the WLAN of your router.
• Additional devices can be connected to the LAN1 (2) and LAN2 (1) network connections.
If the router has already been congured, the password for the WLAN is the same
as that of your output router, otherwise WLAN is unencrypted.
d) Logging in to the device’s web interface
Conguration address http//:ap.setup
IP address (default) 192.168.10.1
Login admin
Password admin
WLAN SSIDs WLAN SSID ‘renkforce-2.4G’, ‘renkforce-5G’
e) Accessing the web interface and basic conguration (all operating modes)
Connect your computer to the device. 2 options are available:
- With cable
- Wirelessly via WLAN
1. Connect a suitable network cable (not included) to an available network connection
(LAN1 (2) or LAN2 (1)) to connect the computer to the device’s network via cable. You can
connect up to 2 devices.
• Connect your computer to the device’s network via WiFi. To do this, activate the WLAN
connection on the device to be connected. Log in to the network with the SSID.
• Open the conguration address (http//:ap.setup) or use the internal/private network IP
address 192.168.10.1 in a web browser.
• Select the desired language from the drop-down menu.
• Log in to the web interface. The login and password are the same:
- Login admin
- Password admin
• Set up the basic conguration in ‘System Setup’. Set your location and time zone and
assign your own password.
Observe the general guidelines for creating a secure password (10 digits long).
• Conrm your settings with ‘Next’ and conrm the overall settings at the end of the process.
Use your new password when logging in again later.
Conguring operating modes
You can now select the operating mode in which you wish to operate the device using the
conguration wizard.
a) ‘LAN bridge (AP mode)’
The device connects to an existing router with internet access via an Ethernet cable and provi-
des internet access to your network devices.
• Connect the device to a router with an internet connection using a network cable (CAT5).
Terminal devices connected to the device via WLAN can access the internet via this con-
nection.
b) ‘WiFi extender (repeater mode)’
In this operating mode, the device connects to an existing router and provides internet access
to your network devices. In this operating mode, the device connects to the output router via
WiFi and creates a connected network (different SSID).
• Select the WLAN to which you wish to connect the repeater or amplify from the list. Always
refresh the list of existing WLANs. After selection, the name of the WLAN is automatically
adopted by your router. In addition, a sufx is also added to the name. You can change this
if you wish.
• Enter the password of the WLAN network that you previously selected. Conrm your chan-
ges. These are applied.
c) ‘Router’
In this operating mode, the device connects to the your ISP’s internet access and provides
internet access to your network devices. Connect a computer or mobile device to the WLAN or
the LAN port of your WLAN AP in order to carry out the conguration.
• After completing the basic conguration, start ‘Setup’.
• Select the type of internet access you would like. For example, if you have a DSL connec-
tion and access data, select PPPoE here.
• Enter the full username and password for your DSL connection in the appropriate elds.
Check the information provided by your ISP for details of your connection settings,
e.g. static or dynamic IP address assignment, etc.
• Then, if desired, change the two names of the WLAN networks (2.4 and 5 GHz).
• Now select an encryption type for the WLAN. We recommend that you select the standard
WPA2-PSK here, as it offers the highest level of security. If you have devices that only
support WPA, select both standards.
• Enter a password for the WLAN. Ideally, it should be 10 characters in length and consist of
numbers as well as upper and lower case letters.
• Finally, conrm. Once the changes have been applied, setup is complete.
d) Restoring factory settings
Follow the steps below to restore the factory settings:
• Connect the device to the power supply.
• Wait until the startup process completes.
• To reset the system to the factory settings, press and hold the Pair Reset WPS button (5)
for 6 seconds. Then release the button.
• The product will restart and the factory settings will be restored.
Care and cleaning
• Disconnect the product from the power supply before cleaning.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may
damage the enclosure or cause the product to malfunction.
• Use a dry, lint-free cloth to clean the product.
Declaration of Conformity (DOC)
Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declares that this
product conforms to Directive 2014/53/EU.
Click on the following link to read the full text of the EU Declaration of Conformity:
www.conrad.com/downloads
Select a language by clicking on the corresponding ag symbol, and then enter
the product order number in the search box. The EU Declaration of Conformity is
available for download in PDF format.
Disposal
Electronic devices are recyclable waste and must not be placed in household waste.
At the end of its service life, dispose of the product in accordance with applicable
regulatory guidelines.
You thus full your statutory obligations and contribute to environmental protection.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Renkforce WS-WN530HP3-A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Renkforce WS-WN530HP3-A in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1.07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info