536366

Renkforce RF1000 Manual

101
Zoom out
Zoom in
Previous page
1/114
Next page
101
e) Nozzle Change
Caution: Danger of burns. Do not touch the hot nozzle or the extruder directly.
• To replace the extruder nozzle, the extruder must first be heated to a temperature suitable for the inserted filament material.
• When
the temperature is reached, remove the inserted filament material as described in “Filament Change”.
• Screw o the extruder nozzle (1) from the extruder with a 10 mm hexagon wrench (2). Always secure the extruder against twi
-
sting at the flattened area of the nozzle thread above the nozzle with the enclosed nozzle wrench (3).
The extruder must not twist during nozzle change and the nozzle must never be turned when cold since the cement
layer above the nozzle may break otherwise. This will render the extruder useless.
• Clean the thread at the extruder of filament residue (e.g. with a brass brush).
• Coil
a piece of sealing tape of about 5 cm around the nozzle thread at the extruder and carefully screw the new nozzle onto the
extruder. Secure the extruder against twisting again with the enclosed nozzle wrench.
Do not wrap the sealing tape beyond the nozzle thread since the nozzle will clog otherwise. We recommend our PTFE
high-temperature tape from the accessory programme of the 3D printer.
• Carefully screw in the new extruder nozzle. Never apply any strong forces for this.
• Then insert the filament again as described in “Filament Change”.
• Switch o the extruder heating again and have the extruder cool o.
20. Handling
• Never connect the mains plug to a mains socket immediately after the device has been taken from a cold to a warm environ-
ment. The resulting condensation may destroy the device. Allow the device to reach room temperature before connecting it.
Wait until the condensation has evaporated.
• Never pull the mains plug from the mains socket by the cable. Only pull it from the mains socket by the intended grip areas.
• Disconnect the 3D printer from the mains voltage if you are not going to use it for an extended period of time.
• Disconnect the mains plug from the mains socket during thunderstorms for reasons of safety.
• The heating plate and extruder may heat up strongly in operation. Do not touch these parts during or just after operation. Let
these parts cool o first.
… 101 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Renkforce RF1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Renkforce RF1000 in the language / languages: English as an attachment in your email.

The manual is 8,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Renkforce RF1000

Renkforce RF1000 User Manual - German - 104 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info