692203
10
Zoom out
Zoom in
Previous page
1/64
Next page
10
If you have questions which remain unanswered by these operating instructions, contact our technical
support service or other technical personnel.
b) Setup
Place the 3D printer on a level, horizontal surface of a sufcient size.
Install the 3D printer in a location that is out of the reach of children.
Ensure that the power switch on the printer is easily accessible so that you can switch it off quickly in
the event of a fault.
Do not expose the printer to extreme temperatures, strong vibrations, high humidity (e.g. rainwater or
steam) or strong mechanical loads.
Never place containers (e.g. glasses or vases) lled with liquid on or directly next to the printer or pour
liquids over the appliance. Liquids may come into contact with the interior components and impair the
electrical safety of the product or cause a re or fatal electric shock.
If the printer comes into contact with liquids, isolate the mains socket (e.g. switch off the circuit breaker
and RCD), and then unplug the mains plug from the mains socket. Disconnect all cables from the printer.
Discontinue use and take the printer to a specialist repair centre.
Do not place open ames (e.g. burning candles) on or next to the printer.
c) Mains cable/connection
The mains socket that the printer is plugged into must be easily accessible.
Only power the product using the mains adapter provided.
Only insert the mains adapter into a standard mains socket that is connected to the public grid. Before
plugging in the power adapter, check whether the voltage stated on the power adapter complies with the
voltage of your electricity supplier.
Fully unwind the mains cable before use, otherwise the cable may overheat and cause a re!
Never connect or disconnect the power adapter if your hands are wet.
Never unplug the power adapter from the mains socket by pulling on the cable. Always use the grips
on the plug.
Make sure that the mains cable is not squeezed, bent, damaged by sharp edges or subjected to
mechanical stress. Avoid excessive thermal stress on the mains cable from extreme heat or cold. Do not
attempt to modify the mains cable, as this may cause permanent damage. Damaged mains cables can
cause a fatal electric shock.
Do not allow the mains cable to hang over the edge of the table or other surface supporting the 3D
printer.
Always lay the cables so that nobody can trip over or become entangled in them, as this may cause an
injury.
For safety reasons, disconnect the power adapter from the mains socket during storms.
Unplug the power adapter if you do not plan to use the 3D printer for an extended period.
Always disconnect the power adapter before leaving the printer unattended.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Renkforce RF100 XL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Renkforce RF100 XL in the language / languages: English as an attachment in your email.

The manual is 7,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Renkforce RF100 XL

Renkforce RF100 XL User Manual - German - 62 pages

Renkforce RF100 XL User Manual - Dutch - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info