Manual Renkforce MH-850T (page 6 of 9) (English, German, Dutch, French)

585218

Zoom out

Zoom in

1/9

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microﬁlming, or the capture in electronic data

processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent

the technical status at the time of printing.

Example for the heating mode

• If the room thermostat serves a frost monitor and should keep the room temperature

of e.g. a storage room or cellar above +5 °C, connect the front outlet of the room

thermostat to a heater, such as a convector.

• Turn off the room thermostat and check which operating mode is currently installed

(“

“ = Heating mode, “ “ = Cooling mode).

• Choose Heating mode as the operating mode.

• Switch on the room thermostat. The control-LED (1) must now light up (LED is red =

the front outlet is deactivated, LED is green = the front outlet is activated).

• Set a temperature limit of +5 °C with the buttons “F“ (7) and “S“ (8). The room ther-

mostat is therefore ready for operation.

• If the room temperature falls under +5 °C for longer than 1 minute, the room ther-

mostat will turn on the connected heater. The control-LED (1) lights up green, and

additionally the symbol “

“ appears.

The time period of 1 minute serves to prevent the connected heater from

being switched on or off in succession too quickly.

• If the room temperature rises higher than +5 °C, the room thermostat turns off the

connected heater again. The control-LED (1) lights up red, and the symbol “

“ dis-

appears again.

Example for the cooling mode

• If the room thermostat is to keep a room from excessively high temperatures, con-

nect the front outlet of the room thermostat to a ventilator for example (or a suitable

air conditioner).

• Turn off the room thermostat and check which operating mode is currently installed

(“

“ = Heating mode, “ “ = Cooling mode).

• Choose Cooling mode as the operating mode.

• Switch on the room thermostat. The control-LED (1) must now light up (LED is red =

the front outlet is deactivated, LED is green = the front outlet is activated).

• Set a temperature limit of +25 °C with the buttons “F“ (7) and “S“ (8). The room

thermostat is therefore ready for operation.

• If the room temperature rises over +25 °C for longer than 3 minutes, the room ther-

mostat will turn on the connected ventilator (or an air conditioner). The control-

LED (1) lights up green, and additionally the symbol “

“ appears.

The time period of 3 minutes serves to prevent the connected air conditioner

from being switched on or off in succession too quickly.

• If the room temperature falls below +25 °C, the room thermostat will turn the con-

nected ventilator (or a air conditioner) off again. The control-LED (1) lights up red,

and the symbol “

“ disappears again.

Maintenance and care

• The product does not require maintenance. The product contains no parts that re-

quire servicing. Therefore, do not open/dismantle it. Maintenance or repair may only

be performed by qualiﬁed personnel or a specialised repair shop.

• Before cleaning, disconnect the room thermostat from the power supply. To do this,

pull it completely out of the mains socket. Then disconnect the room thermostat

from the connected device.

• To clean the product, a clean, dry and soft cloth is sufﬁcient.

• Dust can be easily removed using a clean, soft and long-bristled brush and a vacu-

um cleaner.

Do not use abrasive cleaning agents, rubbing alcohol or other chemical so-

lutions, which may damage the casing or even impair operation.

Disposal

The product must not be disposed of in the household waste!

Please dispose of the product, when it is no longer of use, according to the

current statutory requirements.

Technical data

Connection data ......................................230 V/AC, 50 - 60 Hz

Connection power...................................Ohmic load: max. 3680 W (230 V/AC, 16 A)

....................................................................Inductive load: max. 460 W (230 V/AC, 2 A)

Devices with mainly resistive load are e.g., light bulbs, heaters, etc.

Devices with inductive load are, e.g., engines, control gears, conventional

transformers, energy saving bulbs, etc.

Switch type ..............................................Relay (single-pole)

Temperature setting range ....................+5 °C bis +30 °C

Accuracy ..................................................±1 °C

Backup battery ........................................

yes, built-in permanently (NiMH, 2,4 V, 40 mAh);

Charging time ca. 8 - 12 h, Back-up time ca. 200 h

Socket with child protection .................yes

Ambient conditions ................................. Temperature 0 °C to +40 °C; humidity 20% to

90%, non-condensing

Dimensions...............................................60 x 110 x 77 mm (W x H x D, including plug)

Weight .......................................................136 g

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Renkforce MH-850T in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,29 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Renkforce MH-850T Manual

Product: