700360
9
Zoom out
Zoom in
Previous page
1/12
Next page
ENG
Before you start with the installation of the sound system, disconnect necessarily the GROUND connection wire
from the battery to avoid any risk of electric shocks and short circuits.
NOTE
8 9
ELECTRICAL INTERCONNECTION
BEFORE THE INTERCONNECTION
For the professional installation of a sound system appropriate wiring kits are available in car audio retailer stores. Ensure a
sufcient prole section (at least 10 mm
2
), a suitable fuse rating and a high conductivity of the cables when you purchase your
wiring kit. Clean and remove rust-streaked and oxidized areas on the contact points of the battery and the ground connection.
Make sure that all screws are xed tight after the installation, because loosely connections may cause malfunctions, insufcient
power supply or interferences. We recommend therefore the RENEGADE REN10KIT wire kit.
FUSE
The inserted fuse protects the device against short circuits and overload. The standard fuse rating of 15 A must be
strictly adhered, when you replace a defective fuse.
BATT+
Connect the BATT+12V-terminal with the +12V pole of the vehicle’s battery. Use a suitable cable with a sufcient cross
section (at least 10 mm
2
) and install an additional in-line fuse. For safety reasons the distance between the fuse block and
the battery should be shorter than 30 cm. Do not set in the fuse into the fuse block until the installation is accomplished.
REM (TURN-ON SIGNAL)
Connect the turn-on signal (e.g. automatic antenna) or the turn-on remote wire of your head unit with the REM-terminal
of the sound system. Use a suitable cable with a sufcient cross section (0,5 mm
2
). Thereby the sound system will turn
on or off automatically with your head unit. If your head unit is not equipped with a remote wire, refer to page 10, section
#6. If you use the HIGH LEVEL INPUT like described there, you must not connect the turn-on signal under REM.
GND
Connect this GROUND terminal with a suitable contact ground point on the vehicle’s chassis. The ground wire must be
as short as possible and must be connected to a blank metallic point at the vehicle’s chassis. Ensure that this ground
point has a stable and safe electric connection to the negative “–”pole of the battery. Check this ground wire from the
battery to the ground point if possible and enforce it, if required. Use a ground wire with a sufcient cross section (at least
10 mm
2
) and the same size like the plus (+12V) power supply wire.
1 2 3 4
1
2
3
4
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Renegade RXV1000A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Renegade RXV1000A in the language / languages: English, German as an attachment in your email.

The manual is 0,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info