Manual Renegade RXA1100 (page 9 of 32) (English, German, French, Italian, Spanish)

700338

Zoom out

Zoom in

1/32

IMPORTANT NOTES PRIOR TO INSTALLATION

- This device is only suited for a 12 volt system with negative ground.

- The radiated heat while operation requires sufcient air circulation at the place of installation. It is

very important that the heatsink ns do not have contact with any metal parts or any surfaces which

could impair air circulation. The amplier may not be installed in small closed location or spaces

without air circulation (e.g. spare wheel recess or below the vehicle carpeting). We recommend the

installation in the vehicle’s trunk. Ensure sufcient protection against vibrations, dust and dirt.

- Ensure that the input and output cables are sufciently separated from the power supply cables.

Otherwise interferences may occur.

- Ensure the accessibility of the fuse and the operating elements after installation.

- The reliability and performance of the amplier depends on the quality of installation. Preferably

consult an expert to install the system, particularly if you want to install several loudspeakers.

POWER SUPPLY AND TURN-ON-CONNECTION

INTERCONNECTION

ATTENTION: Before you start with the installation, disconnect the ground connection from the vehicle’s

battery in order to prevent short circuits.

The power wiring which is usually installed in on-board car networks is not sufcient for a power amplier‘s

demands. Make sure that the power wires to GND and to the +12 V terminal has been sufciently specied. A

cable crosssection of at least 10 mm

must be used to connect the battery to the amplier‘s terminals.

First connect the GND terminal of the amplier to an appropriate ground connection at the chassis. To ensure a

good connection, residue dirt and dust from the connection point. A loose connection may cause malfunctions

or interferences noise and distortion.

Then connect the +12 V terminal of the amplier with the battery by using an appropriate cable including

an in-line fuse. This fuse should be located very close to the battery; for safety reasons not more than 30

cm away. Only insert the fuse when the installation, including the connection of the loudspeakers, has been

accomplished.

Then connect the remote turn-on-wire from the headunit with the amplier‘s REM terminal. A cable with a cross-

section of 0.5 mm

is adequate.

LOUDSPEAKER CONNECTIONS

- In 4-channel operation (i.e. one loudspeaker on each amplier channel), the impedance must

not be lower than 2 ohms for each speaker

- In bridging mode (two amplier outputs combined) the impedance must not be lower than 4 ohms

for the bridged output.

- Never connect loudspeaker cables with the ground of the chassis or the +12 V supply voltage.

If the amplier is operated with a too low impedance or incorrectly used, the entire sound system may be da-

maged. This means a warranty void in such cases.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Renegade RXA1100 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 4,03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Renegade RXA1100 Manual

Product: