Manual REMKO SV261 (page 23 of 32) (English)

587850

Zoom out

Zoom in

1/32

Connection to adjacent room

max. 7 m

Adjacent room

Main room

Condensation

connection

If the temperature falls below the

dew point, condensation will form

on the cooling ﬁns during cooling

mode.

A collection tray together with

a condensation pump and ﬂoat

switch are ﬁtted as standard below

the cooling ﬁns. Should the ﬂoat

switch trip a protective shutdown

due to inadequate removal of

the condensation, the pump will

switch on immediately and run on

for approx. three minutes.

■

The condensation pipe should

have a fall of min. 2 %.

This is the responsibility of

the customer. . If necessary,

ﬁt vapour diffusion tight

insulation.

■

If the level of the condensation

pipe on the unit is above

that of the outlet, route the

pipe vertically upwards (max.

1000 mm from the bottom

edge of the unit) and then with

a fall to the drain.

■

The condensation pipe from

the unit should run freely

into the drainage pipe. If the

condensation runs directly

into a sewer pipe, ﬁt a trap to

prevent any unpleasant odours.

■

When operating the unit at

outdoor temperatures below

0 °C, ensure the condensation

pipe is laid to protect it against

frost.

If necessary, ﬁt supplementary

pipe heating.

■

Once the pipe has been laid,

check the condensation drains

off and permanently seal it.

Tightness check

Once all the connections have

been established, the pressure

gauge station is attached as

follows to the Schrader valve (if

ﬁtted):

red = small valve

= injection pressure

blue = large valve

= suction pressure

Once connected, perform a

tightness test using dried nitrogen.

The tightness test involves

spraying a leak detection spray

onto the connections. If bubbles

are visible, the connections have

not been properly made. Re-

tighten the connection or prepare

a new ﬂange.

If the tightness test is successfully

completed, depressurise the

refrigerant pipes and start a

vacuum pump with an absolute

ﬁnal partial pressure of min. 10

mbar to remove the air in the pipe.

Any humidity present in the pipes

is also removed.

A vacuum of min. 20 mbar

abs. must be created!

CAUTION

The time required to generate

the vacuum is dependent on

the pipework volume of the

indoor unit and the length of the

refrigerant pipes. This always takes

at least 60 minutes.

Once any foreign gases and

humidity have been completely

extracted from the system, the

valves on the pressure gauge

station are closed and the valves

on the outdoor component are

opened as described in the chapter

on "Commissioning".

Entry of

fresh air

Inside Outside

Fresh air intake

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of REMKO SV261 in the language / languages: English as an attachment in your email.

The manual is 3,15 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO SV261

REMKO SV261 User Manual - German - 32 pages

REMKO SV261 User Manual - Dutch - 32 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

REMKO SV261 Manual

Product: