726581
29
Zoom out
Zoom in
Previous page
1/84
Next page
The following instructions describe the installation
of the cooling cycle and the assembly of the indoor
unit and the outdoor unit:
1. The required pipe diameters are given in the
table "T
echnical data".
2. Install the indoor unit and connect the refrig-
erant piping as described in the operating
manual for the indoor unit.
3. Use the wall or floor brackets to fit the out-
door unit against structural parts approved to
support the static load (refer to the installa-
tion instructions for the brackets).
4. Ensure that structure-borne sound is not
transferred to parts of the building. Use vibra-
tion dampers to reduce the ef
fects of struc-
ture-borne sound!
5. Lay the refrigerant piping from the indoor unit
to the outdoor unit. Ensure that the fasten-
ings are adequate and if necessary
, take
appropriate oil return measures!
6. Remove the factory-fitted protective caps and
union nuts on the connections. These should
be used later in the installation process.
7. Before flanging the refrigerant piping, ensure
that the union nut is fitted on the pipe.
8. Prepare the laid refrigerant piping as shown
below (
Fig. 31 and Fig. 32).
9. V
erify that the shape of the flange is correct
(Fig. 33).
10. First connect and hand-tighten the refrigerant
piping to ensure it is correctly seated.
11. Then tighten the fittings with 2 appropriately-
sized open-ended spanners. Use a spanner
to counter the force when tightening the fit-
ting (Fig. 34).
12. Use insulation hoses which are designed for
this temperature range and are dif
fusion
proof.
13. Observe the permitted bending radius for the
refrigerant piping during installation. Never
bend a pipe twice in the same place. Brittle-
ness and cracking can result.
14. Apply appropriate heat insulation to the
installed refrigerant piping, including con-
nector
.
15. T
ake the same action at the shut-off valves
for all subsequent refrigerant piping.
2
1
Fig. 31: Deburring the refrigerant piping
1: Refrigerant piping /2: Deburrer
1
Fig. 32: Flanging the refrigerant piping
1: Flanging tool
Fig. 33: Correct flange shape
29
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO RVD 355 DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO RVD 355 DC in the language / languages: English as an attachment in your email.

The manual is 5,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO RVD 355 DC

REMKO RVD 355 DC User Manual - German - 84 pages

REMKO RVD 355 DC User Manual - Dutch - 84 pages

REMKO RVD 355 DC User Manual - French - 84 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info