587735
18
Zoom out
Zoom in
Previous page
1/28
Next page
18
5. Remove the preinstalled swivel nuts of the units.
6. Use only the preinstalled swivel nuts for further as-
sembly.
7. Before you flare the refrigerant lines, ensure that
there is a swivel nut on the hose.
uneven
thickness
formation
of cracks
formation
of cracks
rippled CORRECT
9. Make sure that the flare has the correct shape.
10. First manually connect the refrigerant lines with the
shut-off valves and the bolts to ensure that they are
in the proper position.
11. Now tighten the bolts using 2 hexagonal wrenches
that have a large enough opening.
12. Use a second wrench to apply counterpressure
when tightening.
See figure.
Installation
Installation is performed as follows:
1. The required line cross-sections are provided in the
"Technical Data” table.
Only use refrigerant lines with refrigerator quality.
2. Decide on a drainage option for the indoor unit and
cut the refrigerant connection line hose accordingly.
3. When assembling the unit, observe the bending radii
of the refrigerant lines and never bend the hose in
the same place twice.
This may cause the line to become brittle or crack.
4. Use the following tools for assembly:
G
Only tools approved for use in cold conditions may
be used.
13. Insulate the installed refrigerant lines including the
connector against heat.
14. Only use insulation hoses sealed against diffusion
that are suitable for this temperature range.
15. If you have selected Option 2 or 4 (drainage through
the wall), guide the condensation water and control
line through the wall lead-through to the indoor unit.
If you also need a condensation pump, it must be in-
stalled beforehand.
16. Hang the indoor unit leaning slightly to the back in
the previously assembled wall mount and press the
bottom of the unit into the mount.
17. Place the refrigerant lines between the indoor unit
and the outdoor part.
Make sure that they are adequately secured and if
necessary, take steps to ensure oil recirculation !
Counterpressure
Hexagonal wrench 2
Counterpressure
Hexagonal wrench 1
4. Loosen the screws and detach the wall mount from
the unit.
5. Attach the wall mount and hang the unit in the
mount.
6. Secure unit with the screws into the wall mount.
7. After the unit has been mounted, the disassembled
housing panels must be reattached in the reverse or-
der.
8. Work with the refrigerant lines as shown in the fig-
ure below:
Deburrer
Refrigerant line Flare tool
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO RKS371H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO RKS371H in the language / languages: English as an attachment in your email.

The manual is 1,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO RKS371H

REMKO RKS371H User Manual - German - 26 pages

REMKO RKS371H User Manual - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info