587735
17
Zoom out
Zoom in
Previous page
1/28
Next page
17
Assembling the indoor unit
Prior to assembling the indoor unit, observe the follow-
ing:
àWhen assembling the indoor unit, make sure that the
required minimum distances are observed.
àAssemble the indoor unit in such a way that conden-
sation drainage is not blocked and air can always
flow freely in and out of the unit.
àThe unit is attached by means of a wall mount.
àThe wall mount is attached with screws and dowels
suitable for the wall.
The dimensions of the individual unit types relevant
for attaching them can be found in the section
“Dimensions.
Oil recirculation
If the outdoor part is set up at a higher level than the in-
door unit, appropriate steps must be taken for oil recir-
culation.
This is usually accomplished by creating an oil elevation
arc that is installed every 2.5 meters of line going up.
Example for Options 2 and 4
Disassembling the wall mount
To assemble the wall mount, parts of the housing panel
of the indoor unit must be disassembled.
1. Place the indoor unit with the backside facing up on
a soft surface.
2. Remove the left housing panel from the guiding
slots.
3. Proceed the same way to remove the right housing
panel from the guiding slots.
àPrior to assembly, look at the possible drainage op-
tions (1 to 4) for refrigerant lines, condensation
hoses and control lines.
àIf the outdoor part is set up in a basement, an attic,
in adjoining rooms or halls, make sure that the warm
air can be adequately released.
àInstall an additional fan that has the same air volume
current at its disposal as the outdoor part set up in
the room which can potentially compensate for addi-
tional pressure losses through air channels.
Radius:
50 mm
Outdoor part
max. 5 or
8 m
Indoor unit
Oil elevation arc in the
suction line to the outdoor
part 1x for every 2.5 m
Option 1
Option 3
Option 2
Option 4
Light
shaft
additional
fan
outdoor
part
Warm air
Light
shaft
Warm air Cold
fresh air
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO RKS371H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO RKS371H in the language / languages: English as an attachment in your email.

The manual is 1,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO RKS371H

REMKO RKS371H User Manual - German - 26 pages

REMKO RKS371H User Manual - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info