587737
21
Zoom out
Zoom in
Previous page
1/28
Next page
21
Wiring Diagram
Connecting the outdoor part
The connections of the outdoor part are located inside
the unit above the connection valves. Proceed as fol-
lows to connect the lines:
1. Remove the cover of the terminal strip on the right-
hand side of outdoor part.
2. Guide the lines through the strain relief.
3. Connect the customer-supplied connection lines of
the units to the outdoor part and the indoor unit as
shown in the figure below.
4. Also connect the sensor line of the RKS 350 H unit
to the corresponding connections on the outdoor part
and indoor unit.
5. Secure the control lines in the strain relief and re-
place the cover of the terminal strip.
Condensation
Condensation flow to the outdoor part
Condensation forms during heating operation on the
plate fin exchanger of the outdoor part because tem-
peratures below the dew point are reached.
The lower housing panel of the outdoor part is designed
to function as a drain tray. A condensation connection
has been supplied beneath the condenser or in the cen-
tre of the tray to be used by means of the seal.
If the unit is used for heating in areas susceptible to
frost, the lower housing panel must be kept free of frost
to ensure that the condensation can always drain out.
Condensation drainage on the indoor unit
Condensation forms during cooling operation on the
plate fin exchanger of the outdoor part because tem-
peratures below the dew point are reached.
The drainage trays of the indoor units are equipped with
a condensation hose. This hose must be placed at an
incline to ensure that the condensation drains.
Condensation hose on the outdoor part
Condensation can be guided over longer distances us-
ing a customer-supplied condensation hose.
Ensure the following before laying the condensation
hose:
àMake sure that there is an adequate incline for drain-
age.
Minimum of 2 %.
àWhen the unit is in operation at an outside tempera-
ture of below 0 °C, the hose must be protected
against frost.
If necessary, use a hose heating mechanism.
àAlways use suitable hose clips.
àAfter the hoses have been put into place, you must
check that the condensation flows freely.
1. Place the seal on the hose
connection piece.
2. Press the connection piece
into the opening for this pur-
pose.
Seal
Connection
piece
Resulting
connection
Assembling the condensation connection
RKS 327 H and RKS 335 H
Outdoor part
Compressor control
Neutral conductor
To the reverse valve
Protective conductor
1
N(2)
3
To the condenser fan
PE
4
N
L
PE
N
L
PE
Power suppl
y
Indoor unit
1
N(2)
3
230 V~,
50 Hz,
L1/N/PE
PE
4
RKS 350 H
Outdoor part
Compressor control
Neutral conductor
To the reverse valve
Protective conductor
1
N(2)
3
To the condenser fan
PE
4
N
L
PE
N
L
PE
Power suppl
y
Indoor unit
1
N(2)
3
230 V~,
50 Hz,
L1/N/PE
PE
4
Sensor line to the AT
Sensor line to the AT
Plug
Plug
RKS 371 H
N
L
PE
N
L
PE
Power suppl
y
Indoor unit
230 V~,
50 Hz,
L1/N/PE
Outdoor conductor
Neutral conductor
To the reverse valve
To the condenser fan
Protective conductor
To the compressor
Sensor line
Sensor line
Not in use
N(2)
3
4
PE
5
1
7
8
N(2)
Outdoor part
3
4
PE
5
1
7
8
6
contactor
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO RKS335H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO RKS335H in the language / languages: English as an attachment in your email.

The manual is 1,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO RKS335H

REMKO RKS335H User Manual - German - 28 pages

REMKO RKS335H User Manual - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info