587567

REMKO RKL350 Manual

9
Zoom out
Zoom in
Previous page
1/16
Next page
9
Timer Operation
The timer can be preset to switch the unit on or off for a
maximum of 12 hours. Pressing the “SET” button in-
creases the time until the unit is switched on or off by
one hour.
The number of hours is shown on the display.
Timer switches unit off automatically:
1. W hen the unit is on, press the
“SET” button; the “OFF” LED lights up.
2. Set the desired amount of time until the unit is
switched off with “SET” button.
Keep in mind that after the setting has been made,
the display changes to show the target temperature.
3. After the set amount of time has elapsed, the unit
switches off automatically.
Timer switches unit on automatically:
The unit switches on with the most recently made set-
tings. If you want different settings, you must switch the
unit on, make the changes and then switch the unit off
again.
1. When the unit is switched off, press the “SET” but-
ton ; the “ON” LED lights up.
2. Set the desired amount of time until the unit is
switched on with the “SET” button.
Keep in mind that after the setting is made, the dis-
play changes to show the target temperature.
3. After the set amount of time has elapsed, the unit
switches on automatically.
Initial Operation
Prior to initial operation, the air intake and outlet open-
ings must be inspected for foreign bodies and the air in-
take filter for dirt. Blocked or dirty grilles and filters must
be cleaned immediately. See the chapter “Maintenance
and Service“.
Cooling mode
1. Switch the unit on with the “I/O” button.
2. Select cooling mode with the “Mode” button.
The “AUTO” LED must be lit up.
3. Set the target temperature you want with the
“THERMO CONTROL” buttons.
The selected target temperature appears on the
display.
4. If the set fan speed is too high or too low, the de-
sired fan speed can be set by pressing the “MODE”
button.
Fan mode (circulation)
1. Switch the unit on with the “I/O” button
2. Select fan mode with the “MODE” button. The “FAN”
LED must be lit up.
Information about timer mode (timer clock)
The timer function is reset by pressing the “I/O” but-
ton.
If the “SET” button is pressed while the timer is acti-
vated, the remaining time is shown on the display
and can be changed using the same “SET” button.
If the timer is programmed, this setting may be lost if
the unit is disconnected from the power supply.
Shutting Down the Unit
To shut down the unit, always switch it off with the
“Power” button on the control panel or via the remote
control. Only now can you unplug it from the power sup-
ply. Never shut the running unit off by pulling the power
plug.
Storage
If the unit is to be taken out of operation for a longer pe-
riod of time, for example, over the winter, proceed as
follows:
1. Let the device run for approximately 2 hours in circu-
lation mode (FAN) to dry the surface of the evapora-
tor plate fins.
This removes the remaining moisture from the unit
and prevents unpleasant odours when the device is
put back into operation.
2. Switch off the unit by pressing the “I/O” button, un-
plug the unit from the power supply and roll up the
power cord.
3. Make sure that the cable is not bent and there are
no kinks.
The cable can be attached to the back of the unit.
4. Place a suitable container under the condensation
drain of the internal tank.
The condensation drain is located at the bottom at
the back of the unit.
5. Pull the plug from the condensation drain and collect
the water that drains out.
6. Then replace the plug.
Keep in mind that if there is no plug or it is inserted
incorrectly, water may leak out after the unit has re-
sumed operation.
7. Store the unit in an upright position in a dry location
that is protected from direct sunlight and dust.
8. To prevent dust from getting inside the unit, protect it
with, for example, a plastic cover.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO RKL350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO RKL350 in the language / languages: English as an attachment in your email.

The manual is 3,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO RKL350

REMKO RKL350 User Manual - German - 16 pages

REMKO RKL350 User Manual - Dutch - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info