587902
6
Zoom out
Zoom in
Previous page
1/28
Next page
6
REMKO PGT (E) series
Unit description
The units are mobile fan-assisted
air heaters (WLE) directly fired
with liquid gas, without a heat
exchanger.
The units operate without
an exhaust gas connection
and are designed exclusively
for commercial use.
The units are equipped with
integrated power regulation
for the stepless control of
the heating capacity, quiet and
low-maintenance axial fans,
robust gas burners with thermal
flame monitoring, electric solenoid
valves, electric ignition, room
thermostat socket and mains cable
with earthed safety plug.
The units conform to
the fundamental health and safety
requirements of the appropriate
EU stipulations, and are simple
to operate.
The units are EC type-tested,
DVGW-registered and approved
for EU countries.
The units may be used among
other things for the following:
Drying newly completed
buildings
Spot heating of outdoor
workplaces
Spot heating workplaces
in open, non-flammable
manufacturing facilities and
halls
Temporarily heating enclosed
spaces with a sufficient fresh air
supply
De-icing machines, vehicles and
non-combustible warehoused
goods
Maintaining the temperature
of frost-sensitive parts
Operating sequence
Moving the operating switch
to the “I” position puts
the supply air fan into operation
and the program sequence
for the automatic burner is started.
After a few seconds, the electric
solenoid valve opens the gas
supply to the burner. The liquid
gas is transported through a nozzle
under pressure into the mixing
tube. Here, the gas is enriched
with a quantity of oxygen aligned
with the unit output.
The gas/air mixture is ignited
at the burner head by an
electric ignition spark. Ignition
is automatically ended as soon
as a flawless flame burns, and
the automatic burner has taken
over the flame monitoring.
Regulation of the min/max heating
capacity can be implemented on a
stepless basis during unit operation
on the integrated “power
regulation”.
Monitoring the units
It is possible to safely monitor all
functions with the safety devices
of the units.
In the event of irregularities or if
the flame is extinguished, the units
are switched off and interlocked.
Safety
temperature limiter (STB)
The units are equipped with a
safety temperature limiter (STB),
which interrupts the gas supply in
case of overheating and electrically
interlocks the unit.
A manual reset of the STB can only
be implemented after the units
have cooled down.
The STB is reset by actuating
the reset key 2.
1. Unscrew the protective cap 1.
2. Push in key 2.
3. Screw the protective cap 1 back
on again.
Automatic burner
In the event of irregularities
or if the flame is extinguished,
the automatic burner switches
off and interlocks the units.
The unit's fault lamp will light up
in this case.
The automatic burner is unlocked
by pressing the malfunction
button.
The automatic burner can
be unlocked after a waiting time
of approx. 60 sec.
1
2
CAUTION
If the safety temperature
limiter has been triggered,
the cause of the malfunction
must be identified and rectified
before a reset is performed.
NOTE
Before resetting safety
equipment, the cause
of the malfunction must
be identified and rectified.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO PGT 60E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO PGT 60E in the language / languages: English as an attachment in your email.

The manual is 1,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO PGT 60E

REMKO PGT 60E User Manual - German - 28 pages

REMKO PGT 60E User Manual - Dutch - 24 pages

REMKO PGT 60E User Manual - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info