587706
13
Zoom out
Zoom in
Previous page
1/28
Next page
Control line
Condensation line
Injection pipe
Suction pipe
PVC tube
1
Pipes and cables in wall breakthrough
Selection of the installation
location
The outdoor unit is designed for
horizontal free-standing use in
outdoor areas.
It should be placed on level,
flat and firm ground. The unit
should also be secured to prevent
toppling.
The outdoor unit can be installed
both inside and outside buildings.
In the case of outdoor installation,
please follow the instructions given
below to protect the unit against
the weather.
Rain
The unit should be at least 10 cm
off the ground when mounted on
the roof or ground.
An optional floor bracket is
available as an accessory.
Sun
The liquefier on the outdoor unit
radiates heat.
Exposure to direct sunlight will
further increase the temperature
of the fins and reduce the heat
output of the liquefier.
The outdoor unit should therefore
be installed as near as possible to
the north side of the building.
If necessary, take measures
to provide sufficient shade
(responsibility of customer). One
possible solution is to build a small
roof.
However, the discharging warm air
flow may not be affected by the
measures.
Wind
If the unit is being installed
in windy areas, ensure the air
discharges in the prevailing wind
direction. If this is not the case
it may be necessary to install
a windbreak (provided by the
customer) (Figure 2).
Ensure that the windbreak does
not adversely affect the air intake
to the unit.
Wind
2 Windbreak
20 cm
Snow
3 Minimum clearance to snow
Snow
The unit should be wall-mounted
in areas of heavy snowfall.
Installation should then be min.
20 cm above the expected level
of snow to prevent snow from
entering the outdoor unit (Fig 3).
An optional wall bracket is
available as an accessory.
Installation inside buildings
Ensure there is adequate heat
dissipation when placing the
outdoor unit in cellars, attics,
adjoining rooms or halls
(Figure 4).
Install an additional fan with
a rated flow comparative to
that of the outdoor unit being
installed in the room. This
is used in conjunction with
ventilation ducts to compensate
any pressure losses
(Figure 4).
Ensure a continuous and
unobstructed air flow from
outside, preferably using
sufficiently large air inlets
(Figure 4).
Comply with any regulations
and conditions affecting
the statics of the building.
If necessary, fit acoustic
installation.
Warm air
Cold
Fresh air
Light
well
Outdoor unit
Warm air
Light
well
Additional
fan
4 Installation inside buildings
13
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO MVT900 DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO MVT900 DC in the language / languages: English as an attachment in your email.

The manual is 1,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO MVT900 DC

REMKO MVT900 DC User Manual - German - 24 pages

REMKO MVT900 DC User Manual - German - 28 pages

REMKO MVT900 DC User Manual - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info