587706
11
Zoom out
Zoom in
Previous page
1/28
Next page
Display Cause Required action
E0 EEPROM error
Switch off the power to device for 1 min.
Contact specialist dealer
E1 Sensor suction pipe circuit 1 faulty / connection interrupted
Check the resistance of the sensor
( at 20°C=12.6k / 30°C=7.9kΩ)
E2 Sensor suction pipe circuit 2 faulty / connection interrupted
Check the resistance of the sensor
( at 20°C=12.6k / 30°C=7.9kΩ)
E3 Sensor suction pipe circuit 3 faulty / connection interrupted
Check the resistance of the sensor
( at 20°C=12.6k / 30°C=7.9kΩ)
E4 Sensor discharge liquefier faulty / connection interrupted
Check the resistance of the sensor
( at 20°C=12.6k / 30°C=7.9kΩ)
E5 Compressor voltage monitoring has tripped Switch off the power to device for 1 min
E6 Sensor suction pipe circuit 4 faulty / connection interrupted
Check the resistance of the sensor
( at 20°C=12.6k / 30°C=7.9kΩ)
E7 Communication error between outdoor and indoor unit Contact specialist dealer
P0 Excessive temperature (Klixon) compressor
Check refrigerant
Check the resistance of the compressor
sensor (normal 0)
P1 High pressure sensor has responded
Check refrigerant filling level,
check liquefier for soiling,
check fan AT
P2 Low pressure sensor has responded
Check stop valve AT, check refrigerant,
check electronic expansion valves,
P3 Overcurrent compressor has responded
Check winding resistance of the
compressor (1 = U-V / U-W / V-W)
P4
LED AT
flashes 9 times
Rotational speed monitoring on compressor has responded Check compressor connections and PCB
P4
LED AT
flashes 13 times
Rotational speed monitoring on compressor (inverter module)
has responded
Check connections CN4, CN1 on the AT PCB
Contact specialist dealer
P5 Excess temperature sensor on outdoor unit unit has responded Exterior temperature > 1h under -15°C
P6
Sensor outlet liquefier has responded
(Condensation temperature over 65°C)
Clean liquefier
Reduce air inlet temperature
Problem display by blinker code
11
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO MVT900 DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO MVT900 DC in the language / languages: English as an attachment in your email.

The manual is 1,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO MVT900 DC

REMKO MVT900 DC User Manual - German - 24 pages

REMKO MVT900 DC User Manual - German - 28 pages

REMKO MVT900 DC User Manual - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info