587699
21
Zoom out
Zoom in
Previous page
1/28
Next page
Connecting the outdoor
component
Proceed as follows to connect the
cable:
1. Remove the cover from the
unit.
2. Remove the side panel next to
the terminals.
3. Select the cable cross-section
according to the relevant
standards.
4. Feed both cables through the
edge protection rings on the
fixed connection panel.
Electrical connection diagram
Connections ML 261 to ML 521
Check all plugged and clamped
terminals to verify they are
seated correctly and making a
permanent contact. Re-tighten
as required.
CAUTION
5. Terminate the cables as shown
on the electrical connection
diagram.
6. Support the cable in the strain
relief and re-assemble the unit.
(Fig 12).
12
Connecting the outdoor unit
Outdoor
component
Indoor unit Mains cable
Earth conductor
Neutral conductor
Phase conductor
Reverse flow valve
rear
terminal
block
front
terminal
block
230 V~,
50 Hz,
L1 / N
/ PE
Control
conductor
Compressor contator
PE
NN
PE
3
2
3
PE
N
L L L
2
11
Control
conductor
Control
conductor
Fan motor
Neutral conductor
Phase
conductor
Connection ML 681
Outdoor
component
Indoor unit Mains cable
Neutral conductor
Phase conductor
Reverse flow valve
230 V~,
50 Hz,
L1 / N
/ PE
Control
conductor
Compressor contator
N
L1
PE
L
N
3
2
3
N
L
2
1
PE
1
PE
Control
conductor
Control
conductor
Earth conductor
Fan motor
front
terminal
block
Connecting the indoor unit
Make the connection as follows:
1. Open the air intake guard.
2. Unfasten the cover on the right
side and at the bottom right
rear (Fig 11).
3. Connect the unit to the
control cable from the outdoor
component (to be provided
by customer). See electrical
connection diagramOn the
ML 681 IT series, the terminal
block for the mains supply
and control contacts is located
behind the front cover.
4. Re-assemble the unit.
11
Connecting the indoor unit
front terminal block
control cable
from outdoor unit
Cover rear terminal block
supply voltage
from outdoor unit
Cover
21
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO ML 351 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO ML 351 in the language / languages: English as an attachment in your email.

The manual is 4,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO ML 351

REMKO ML 351 User Manual - German - 28 pages

REMKO ML 351 User Manual - Dutch - 28 pages

REMKO ML 351 User Manual - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info