726822
53
Zoom out
Zoom in
Previous page
1/60
Next page
13 Troubleshooting and customer service
The unit and components are manufactured using state-of-the-art production methods and tested several
times to verify that they function correctly
. However, if malfunctions should occur, please check the functions
as detailed in the list below. For systems with an indoor unit and outdoor unit, refer to the chapter "Trouble-
shooting and customer service" in both operating manuals. Please inform your dealer if the unit is still not
working correctly after all function checks have been performed!
Operational malfunctions
Malfunction Possible causes Checks Remedial measures
The unit does not
start
Display is not illuminated.
No power supply, power
failure, device fuse / main
switch switched of
f / defec-
tive
Check the power connec-
tions on the general supply
terminals and the voltage
values. Check the unit fuse,
the main switch and the
fuses on the secondary side
of the additional trans-
former.
The display lights up and
shows “Phase sequence
error”.
Incorrect phase sequence.
The phase sequence relay
did not issue an enable
signal.
Swap the phase conductors
of the power supply on the
terminal block on the con-
trol panel.
Display shows status: “Off”.
The unit is deactivated.
Change the operating
status in the “A. On / Of
f
Unit” submenu
The controller emits an
acoustic signal.
One or more protective
devices have tripped. A
malfunction is present.
Check error messages, rec-
tify the malfunction,
acknowledge the malfunc-
tion (see chapter “Error indi-
cation”).
The compressor icon is dis-
played, but the unit does
not start.
Compressor or compressor
contactor defective.
Have specialist replace
contactor or compressor
.
The unit works at
reduced cooling
capacity
Thermal load too high.
Thermal load was
increased.
If possible, reduce the
thermal load.
Inlet temperature too high.
Return flow temperature set
too high.
Reduce return temperature.
Air in the medium cycle.
Medium cycle not bled, no
automatic bleeding valves
installed.
Manually bleed or install
automatic bleeding valves
at the highest point.
Condenser temperature too
high.
Slats dirty, exposed to
strong sunlight.
Clean fins, provide shade
for the unit, adhere to oper-
ating limits.
Pulse mode because of too
little demand.
System may be over-
dimensioned
Increase medium flow rate
with the installation of a
storage tank.
53
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO KWE serie 150-180-220-250-300-320-370-440 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO KWE serie 150-180-220-250-300-320-370-440 in the language / languages: English as an attachment in your email.

The manual is 2,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO KWE serie 150-180-220-250-300-320-370-440

REMKO KWE serie 150-180-220-250-300-320-370-440 User Manual - German - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info