587907
28
Zoom out
Zoom in
Previous page
1/44
Next page
28
REMKO GPM
Gas connection
LEGEND
1 = Electric gas solenoid valve
Main burner
2 = Electric gas solenoid valve
Ignition burner
3 = Pressure regulator
4 = Electric gas safety valve
5 = Gas filter (small filter area)
6 = Vibration absorbing
connecting piece (locally)
7 = Gas filter with large filter area
(locally)
8 = Gas shut-off valve (locally)
1 2 3 4 5 6 7 8
Arrangement of factory supplied gas components
must be installed by the
installation company
Installation of the gas connection
must only take place by authorised
specialists (approved by the gas
supply company) in compliance
with the regulations applicable to
the respective type of gas.
The cross-section of the cables
must be dimensioned according
to the installed load of the unit,
total line resistance and gas supply
pressure.
The necessary gas supply pressure
(depending on the particular type
of gas) must be ensured locally.
Depending on the capacity of the
unit, the necessary gas volume
and gas pressure must be available
constantly during operation.
Connection of the unit takes place
via a R 3/4“ or R 1“ connection
with external thread.
The gas supply pipe must be
installed stress and vibration-free
using suitable, detachable unions.
The components prescribed in
the pertinent gas directives and
necessary components in the gas
pipe locally must be installed by a
qualified installation company.
Gas pressure reducers, shut-off
devices, etc., are not included in
the factory delivery and must be
provided locally.
The installation of a gas filter
without pressure regulator is also
recommended as the area of the
standard filter installed above the
gas valve is limited.
The applicable standards allow
within rooms or heating rooms a
maximum pressure of 60 mbar;
higher pressures must be reduced
prior to admission into the heating
room or room in which the unit is
installed.
Before using the unit for the first
time, the gas supply pipe must be
thoroughly cleaned and vented by
suitable means.
It must be ensured that the unit
is connected gas-tight to the gas
supply pipe.
All screwed connections of the unit
and gas pipe must be checked for
tightness.
If leak detection sprays are used,
these must comply with DIN
30657 (corrosion-free).
We reserve the right to make changes to dimensions and design in the interest of technological advances.
ATTENTION
Installation of the gas system
and supply pipes must only
be carried out by authorised
specialists.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO GPM 35 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO GPM 35 in the language / languages: English as an attachment in your email.

The manual is 4,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO GPM 35

REMKO GPM 35 User Manual - German - 44 pages

REMKO GPM 35 User Manual - Dutch - 44 pages

REMKO GPM 35 User Manual - French - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info