587925
4
Zoom out
Zoom in
Previous page
1/16
Next page
4
Differential temperature control 2 sensor operation
The ATR-3 electronic clock thermostat gradually controls the speed of
REMKO DVL ceiling fans between 1 and a maximum of 14 and controls
a warm air heater.
The unit works with two sensors: a room temperature sensor at operat-
ing height and a ceiling temperature sensor. Unused warm air that rises
to the ceiling in high rooms is measured by the ceiling temperature sen-
sor.
If the room temperature falls below the set target temperature
(adjustment knobs A und B) and, at the same time, the ceiling tempera-
ture is above the room temperature by a set differential value
(adjustment knob C), the REMKO DVL ceiling fans start running and
transport the warm air down. The warm energy from the ceiling area is
can be used again in the work area.
If the difference in temperature increases, the fan speed also increases
up to the maximum speed. The minimum and maximum fan speeds are
adjustable (adjustment knobs F and G). The fan performance is dis-
played by indicators (M) on the display of the weekly clock timer (K).
If the room temperature falls by a specific, adjustable value (adjustable
knob E) below the target value, the heat also switches on. The operating
mode is displayed by a LED (N)
A digital weekly clock timer with power reserve makes it possible to pro-
gram heating and cooling off periods.
Proportional control 1 sensor operation
To meet special requirements, the unit can also be used for pure propor-
tional control. In this case, the “Heating” and “Cooling” operating modes
may be selected.
In the 1 sensor mode, only the room temperature is measured. If the tar-
get value of the room temperature goes above or falls below the value
set on the control mechanism Xp (D), the ceiling fans start running.
If, during “Heating” mode, the room temperature falls by a specific, ad-
justable value below the target temperature, the heat also switches on.
If the heating relay is not regulated during “Cooling” mode, the air is only
circulated.
In the "Setting the Functions" menu, the operator can switch from dif-
ferential temperature control to proportional control and from heating to
cooling is performed (see page 9).
The second sensor does not have a function. It can be used as a place
to perform measurements (display for 3 seconds after pressing the SET
program button).
Functionality
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO ATR-3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO ATR-3 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO ATR-3

REMKO ATR-3 User Manual - German - 24 pages

REMKO ATR-3 User Manual - Dutch - 16 pages

REMKO ATR-3 User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info