627780

Remeha Gas 310 Eco Manual

11
Zoom out
Zoom in
Previous page
1/20
Next page
11
COMMISSIONING THE BOILER
1. First follow the guidelines that your installer supplied
for the entire installation. If not available: follow the
instructions below.
2. Check the water pressure in the installation
(min. 0.8 bar). Fill up when necessary.
3. Open the main gas cock.
4. Put the boiler control to heat demand.
5. Start the circulation pump.
6. Switch on the electrical supply to the boiler and the
on/off switch on the instrument panel.
7. The following operation course shall successively
appear on the code-display:
5 = Waiting mode; the fan runs and the boiler waits
until sufficient air transport is established (air pres-
sure switch open or closed).
1 = Pre-purging.
2 = Ignition of the gas/air mixture.
3 = The burner is firing.
The boiler now operates.
If this fails to work, switch the boiler to manual operation
(see Chapter “Operation” from the Technical Informa-
tion), set the flow temperature to the desired value and
contact your installer.
PUTTING THE BOILER OUT OF OPERATION
1. First follow the guidelines that your installer supplied
for the entire installation. If not available: follow the
instructions below.
2. Turn off the boiler control.
3. Close the main gas cock.
4. Switch off the electrical supply.
Attention! Think of the risk of freezing!
If temperatures are low, it is recommended to run the
central heating installation at a reduced temperature to
avoid freezing up.
VENTING OF THE INSTALLATION
1. Put the boiler control to heat demand.
2. Open all the radiator valves.
3. Run the installation up to about 80°C.
4. Switch off the electrical supply to the boiler.
5. Wait for approximately 10 minutes.
6. First vent the installation on all the vent points
(boiler, radiators, etc.).
7. Check the water pressure and, if necessary, fill up to
design system pressure; entirely fill the filling hose
before connecting it to the installation.
8. Put the boiler into service again.
Repeat venting procedure, if necessary.
Attention!
A poorly vented installation may cause water flow prob-
lems and air noise in the boiler, the pipework and the
radiators.
TROUBLE SHOOTING
Before calling in the installing engineer, first check if:
- The gas cock is open
- The maximum operating temperature setting is high
enough
- The boiler control has been correctly set
- The main switch is on
- A sufficient water flow is possible
(the radiator valves are entirely opened)
- The water pressure is sufficient (> 0.8 bar).
Note down the failure message before resetting
(3 digits, blinking and dots included). Reset the failure
by pressing the reset-key on the instrument panel. If the
boiler failure is immediately repeated, contact the install-
ing engineer, stating the failure message.
Attention!
Do not forget that your central heating installation needs
servicing once a year.
On gas smell: close main gas cock and warn gas com-
pany or installer.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Remeha Gas 310 Eco at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Remeha Gas 310 Eco in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info