8435
25
Zoom out
Zoom in
Previous page
1/36
Next page
25
10.7 Building Ma na ge ment System
For connection to a Building Management System the
Remeha Gas 3002 ECO is delivered as standard with a
RS 232 connection.
The boiler is also provided with the following potential-
free contacts: - signal 'low'
- signal 'high'
- central alarm.
Standard the signal 'low' is activated if the boiler load is
bet ween minimum and 95%. and the signal 'high' is acti-
vated if the boiler load is between 95% and maximum.
(See also option 6, para. 7.3.3.)
10.8 Frequency changer
The frequency changer controls and delivers a 3-phase
supply of 230V, by which the frequency can vary from
0 to a maximum of 60Hz. This alternation in frequency
controls the speed of the fan motor. The frequency chan-
ger is fi tted in the control panel behind the front casing.
Inside the frequency changer there are two L.E.D.'s, a
green one for 'ready' and a red one for 'fault' indication.
Blinking green L.E.D. means the frequency changer is not
ready. In that case, check the link between terminal 7 and
39, and the link between terminal 20 and 28 (see
wiring diagram).
If the red L.E.D. is blinking the frequency changer fails.
This is caused by:
- Short circuit on the windings of the motor or in the
wiring to the motor.
Check the wiring of the motor and measure the
windings of the motor.
- The motor runs heavy, through which the current
increases.
Check if the fan runs free.
- Frequency changer is too hot.
Check if the cooling rib is too hot and if the frequency
changer is fi tted correctly to the control panel.
By switching on/off the frequency changer will be reset.
10.6 Outputs
10.6.1 Alarm output
The boiler is tted with a potential-free two-way contact
for the alarm or ready message. When the boiler is
locked or dead, contact 11 and 12 will be made. When
the boiler is ready, contacts 11 and 10 will be made.
The maximum load on the contact is 250V/2A.
This output is indicated by the following symbol:
10.6.2 Operating message
The boiler is tted with two potential-free closed-circuit
contacts for the low operating message and the high
operating message. Contacts 13 and 14 are for the low
operating message, and contacts 15 and 16 for the high
operating message. The moment at which a switch is
made from low to high can be programmed at the service
level (see paragraph 7.3.3, option 6).
The symbol for this output is:
10.6.3 External gas valve
If required, an external gas valve can be connected to
terminals 17 and 18. 230V is applied to these terminals
as soon as the fan starts to operate. When the fan
switched off, the voltage is also disconnected. The maxi-
mum power take-up for the gas valve is 0.1A.
The symbol for this output is:
10.6.5 Extra 230V connection
On terminals 8 and 9, the external power supply is once
again diverted outwards for the connection of external
components such as relays and pumps. The voltage on
these terminals is not switched off by the main switch
on the panel. This voltage is also neither fused nor
ltered.
The maximum current across these terminals is 10A, but
will depend on the value for which the power supply to
the boiler is fused. In the switch panel there is a little
free
space for the possible installation of an extra relay.
The symbol for this output is:
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Remeha Gas 3002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Remeha Gas 3002 in the language / languages: Dutch as an attachment in your email.

The manual is 1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Remeha Gas 3002

Remeha Gas 3002 User Manual - German - 28 pages

Remeha Gas 3002 Manual - Dutch - 2 pages

Remeha Gas 3002 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info