716181

Reer 50133 Care and talk Manual

18
Zoom out
Zoom in
Previous page
1/57
Next page
34 35
Child unit (star motif)
Hold down button while turning on device. (Hold down both outer buttons in parallel).
Press / buttons and select bA. The child symbol will be displayed. In order to save
the settings, briefly press the PTT button.
Parental unit (without motif)
Hold down button while turning on device. (Hold down both outer buttons in parallel).
Press / buttons and select PA. The parental symbol will be displayed. In order to
save the settings, briefly press the PTT button.
Now the channel (01 to 18) is displayed, which, on the child unit, is supplemented by the
letter b, or on the parent unit, by the letter P. Then, the corrsponding symbols or
will be displayed.
Using several child units
With the help of several child units, you can monitor multiple children, event. multiple
rooms. For this, all devices must be set to the same channel. When using in this way, we
recommend deactivating reach control, as due to variouse devices, false alarms may occur.
Keep in mind that in the parental unit, you can hear only one child at a given time. Besides
this, you should lower the volume on child units to 0, as otherwise, the children could mu-
tually listen to each other or disturb each other.
Chapter 2: Use in „walkie talkie“ operating moden
Both devices are factory-set to the „baby monitor operating mode. If you wish to re-set the
devices to the operating mode „radio device PMR446“, execute the following steps.
Hold down the button while turning on the device (hold down the OFF/ON button for
several seconds). By pressing the / button, select ro. In order to save the settings,
briefly press the PTT button.
Selection of PMR446 channel
This broadcasting/receiving system has 8 PMR446 channels available. On top of this, you
can select individual PMR446 coding for each channel individually through CTCSS tones (38
possible codes). The code will appear to the right of the number of the channel as a small
two-digit number between 01 and 38 or oF.
Make sure that all devices are set to the same channel and CTCSS tone.
Press button 1× and then choose the required PMR446 channel with the help of /
buttons.
Setting CTCSS or DCS code
Additional CTCSS or DCS codes serve to prevent listening in on other conversations on the
same channel. This does not mean, however, that the transmission is protected against in-
terception. There is always the possibility that unencrypted analog radio signals will be inter-
cepted. CTCSS (Continuous Tone Coded Squelch Signal) or DCS (Digital Coded Squelch) tones
are tones beyond the low frequency audibility threshold, which are transmitted together
with the microphone signal. In case of reception, the device will check whether a CTCSS or
DCS tone is transmitted and will turn on the speaker only when the correct code is received.
Setting the CTCSS code:
Press button once. 01–38 or oF flashes on the display. For setting the required code, press
/ buttons. In order to save the settings, briefly press the PTT button.
Setting the DCS code:
Press the button 2×. 01–38 or oF flashes on the display. For setting the required code,
press / buttons. In order to save the settings, briefly press the PTT button.
Warning: it is possible to activate only CTCSS or DCS.
Transmission
To broadcast, press and hold down PTT button. To receive, let go the button again.
Searching for channels
This function will search all PMR446 channels according to signal. To start search, hold down
button for a long time. The search is interrupted as soon as the signal is captured. You
can then listen to the channel for a period of 8 seconds, until the search continues. After
ending the search, hold down button for a long time once again.
Warning: searching channels is availavle only in the „PMR446“ operating mode.
Ringtone selection
Press button 9×.C will appear on the display, as well as current settings, which will flash.
To select ringtone from possibilities 01-03 or oF, press / buttons. In order to save the
settings, briefly press the PTT button.
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Reer 50133 Care and talk at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Reer 50133 Care and talk in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 17,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info