559720
7
Zoom out
Zoom in
Previous page
1/31
Next page
5. With the help of another person, carefully raise the
Uprights (35, 58) to the vertical position, with the wheels
and the walking platform on the floor as shown on page 5.
Have the other person hold a Handgrip Post (41) on the
Left Upright (35) as shown. Hold a Post Spacer (43) in-
side of the Handgrip Post. Insert a Post Bolt (44) with a
1/4” Washer (125) through the end hole in the Handgrip
Post and through the Post Spacer. Finger tighten the
Post Bolt. Finger tighten another Post Bolt (44) with a 1/4”
Washer (125) into the other hole. If necessary, tap the
Handgrip Post with a rubber mallet to make sure that it is
fully seated. Tighten the Post Bolt in the end hole.
Then, tighten the other Post Bolt.
Attach the other Handgrip Post (41) to the right Upright
(not shown) as described above.
5
125
End
Hole
43
44
41
35
4. Locate the Belly Pan Wire Harness (124). Route the Belly
Pan Wire Harness over the Base (117) as shown.
Connect the Belly Pan Wire Harness to the Wire Harness
(
55). Be sure to insert the connectors properly (see
drawing 4a). IF THE CONNECTORS ARE NOT IN-
S
ERTED PROPERLY, THE CONSOLE MAY BE DAM-
AGED WHEN THE POWER IS TURNED ON. The con-
nectors should slide together easily and snap into
place. If the connectors do not slide easily and snap into
place, turn a connector and try again.
See drawing 4b. Carefully wrap the wires around the con-
nectors as shown. Insert the connectors and the excess
Wire Harness into the Right Upright (58).
With the help of another person, carefully tip the treadmill
onto its other side. Attach the Left Upright, the other Base
Leg, the left Front Wheel, and the other Base Pads (not
shown) as described in steps 1 through 3. (Note: There is
not a wire harness in the Left Upright.) Do not fully
tighten the bolts yet.
4
55
124
117
6
6. Have another person hold the Console Base (52) near
the Uprights (35, 58). Locate the wire harness extending
from the Console Base. Connect the wire harness to the
Wire Harness (55) in the Right Upright. If the connectors
do not fit together easily, rotate them and then con-
nect them. Carefully feed the connectors and the excess
wire harness into the Right Upright. Carefully set the
Console Base on the posts on the Uprights.
Finger tighten four Console Bolts (42) with four Star
Washers (113) into the Uprights (35, 58) and the Console
Base (52). After all four Console Bolts have been started,
tighten them.
See step 1. Tighten the two Upright Bolts (66). See
step 2. Tighten the four Base Leg Bolts (77). Make
sure that the Base Leg Nuts (70) are fully seated in
the square holes. Note: It may be helpful to tip the
treadmill onto its side to tighten the Base Leg Bolts.
113
113
42
42
58
35
52
55
Wire Harness
58
7
4a
4b
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Reebok RX820 TREADMILL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Reebok RX820 TREADMILL in the language / languages: English as an attachment in your email.

The manual is 1,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info