559720
6
Zoom out
Zoom in
Previous page
1/31
Next page
ASSEMBLY
Assembly requires two people. Set the treadmill in a cleared area and remove the packing materials. Do not
d
ispose of the packing materials until assembly is completed. Assembly requires the included allen wrench
and your own 7/16” and 9/16” wrenches , rubber mallet , wire cutters ,
and Phillips screwdriver.
U
se the part chart attached in the center of this manual to identify small parts used in assembly. Each
bag of hardware is labeled with the corresponding assembly step.
1. With the help of another person, carefully tipthe treadmill
onto its left side.Have theotherpersoncontinue tohold
thetreadmillduringsteps1through 4.Note:Only half of
thehardware inthe bags for steps1to3will be used. The
remaining hardwarewill be used at the end ofstep 4.
Identify the Right Upright (58), which contains the Wire
Harness(55).Insertthe roundtubeontheRightUprightinto
theBase (117) as shown.If necessary,applygreaseto
theroundtubeand usearubbermallet. HoldaStarWasher
(113) between the indicatedtab and the Base,and Finger
tightenan Upright Bolt (66) through the tab into the Base.
Make sure that the two indicated Walking Platform
Screws (114) in the Walking Platform (100) are tight.
1
3. See the inset drawing. Identify the right Front Wheel (62)
by observing the direction that the Wheel Bracket (64)
slants.
Attach the Wheel Bracket (64) and the right Front Wheel
(62) to the Base (117) with four 3/4” Screws (12) as
shown.
Attach a Thin Base Pad (103) and a Thick Base Pad (75)
to the Base (117) with two 3/4” Screws (12) as shown.
12
103
12
117
64
75
3
62
117
114
58
100
55
66
113
Tab
64
62
Right
Left
6
2. Attach a Base Leg (78) to the Base (117) with two Base
Leg Bolts (77) and two Base Leg Nuts (70). Make sure
that the Base Pad (75) is in the position shown. (Note:
The Base Leg Nuts fit into square holes in the Base. If
necessary, push or pull on the Right Upright [58] to align
the holes.) Do not fully tighten the Base Leg Bolts yet.
2
75
78
70
117
77
66
58
77
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Reebok RX820 TREADMILL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Reebok RX820 TREADMILL in the language / languages: English as an attachment in your email.

The manual is 1,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info